Extron electronic RGB 560 AKM Installation Overview, Installation and Operation Instructions

Page 13

Installation Overview

Installation Overview

To install the interface, follow these basic steps:

1

2

3

4

5

6

7

8

9

Set the DIP switches, located inside the access panel (see page 2-3), and the gain/peaking adjustment jumpers, located inside the enclosure. (See below.)

Set the front panel video termination toggle switch on the RGB 500 AKM, or set the front panel ID bit DIP switches on the RGB 560 AKM. (See page 2-4.)

Connect the signal output and power cables. (See “Attaching output cables” on page 2-6.)

Temporarily connect the computer video and audio input cables and (for the RGB 560 AKM) the local monitor output cable. (See “Connecting input cables” on page 2-7.)

Connect power cables to the input and output devices. Turn on the input and output devices.

The image should now appear on screen. If it does not appear, or if the picture is displayed incorrectly, double check and make adjustments to cables, DIP switches, and jumpers as needed. (See “Pre-installation testing/ troubleshooting” on page 2-7.)

Temporarily disconnect the computer video cables and the audio input cables and (for RGB 560 AKM) the local monitor output cable from the front panel of the interface.

Install the interface in the Ackermann floor tank.

Reconnect the computer video and the audio input cables and (for

RGB 560 AKM) the local monitor output cable to the interface, and readjust horizontal centering as needed via the front panel knob.

Installation and Operation Instructions

Adjusting the gain/peaking jumpers

Video signals passing through long cable runs (over 125 feet) can decrease in strength, creating signal loss. The longer the cable, the higher the video level and the greater the peaking that will be needed to compensate for the loss.

To change the gain/peaking jumpers, do the following:

Disconnect power before making these adjustments.

1.Remove the faceplate from the enclosure by removing the four screws shown in figure 4, and loosen the two screws shown. Do not pull the output cables out of the enclosure.

RGB 500 AKM and RGB 560 AKM Installation and Operation 2-5

Image 13

Contents Architectural Series Universal Interfaces with Audio and ADSP RGB 500 AKM RGB 560 AKM68-468-02 Printed in the USA Safety Instructions English PrecautionsConsignes de Sécurité Français Sicherheitsanleitungen DeutschRGB 500 AKM and RGB 560 AKM Table of Contents Table of Contentsii RGB 500 AKM and RGB 560 AKM Table of Contents Table of Contents, cont’dChapter1One About the Interfaces FeaturesIntroduction RGB 500 AKM and RGB 560 AKMRGB 500 AKM and RGB 560 AKM features FeaturesIntroduction About the InterfacesRGB 560 AKM features RGB 500 AKM featureRGB 500 AKM and RGB 560 AKM Introduction 1-4 RGB 500 AKM and RGB 560 AKM Introduction Introduction, cont’dFront Panel Features Installation Overview Installation and OperationInstallation and Operation Instructions Chapter2TwoFront Panel Features Installation and Operation2-2 RGB 500 AKM and RGB 560 AKM Installation and Operation Figure 2 - RGB 500 AKM front panelRGB 500 AKM and RGB 560 AKM Installation and Operation eight DIP switches, numbered 1 through 8 from left toright, control sync on green, sync processing, serration pulse, composite sync output , force negative syncComputer video input 9-pin D male connector RGB 500 AKM only Installation and Operation, cont’dComputer video input 15-pin HD female connector RGB 560 AKM only 10 Front panel DIP switches RGB 560 AKM onlyInstallation and Operation Instructions Installation OverviewAdjusting the gain/peaking jumpers of the maximum peaking to the signal Figure 4 - Setting the gain/peaking jumpersAudio output connector 2-6 RGB 500 AKM and RGB 560 AKM Installation and OperationPre-installation testing/troubleshooting Connecting input cablesFigure 5 - Wiring for audio output Power connectorFigure 6 - Typical RGB 500 AKM and RGB 560 AKM applications 2-8 RGB 500 AKM and RGB 560 AKM Installation and OperationAAppendix A SpecificationsA-2 RGB 500 AKM and RGB 560 AKM Specifications SpecificationsVideo Video inputAudio input RGB 500 AKM and RGB 560 AKM Specifications A-3Audio output GeneralA-4 RGB 500 AKM and RGB 560 AKM Specifications Specifications, cont’dAppendixBB Interfaces Cables Other AccessoriesPart Numbers Interfaces Part NumbersCables RGB 500 AKMHigh-resolution cables Other AccessoriesRGB 500 AKM and RGB 560 AKM Adapter laptop breakout cables Part numberB-4 RGB 500 AKM and RGB 560 AKM Part Numbers Part Numbers, cont’dEurope, Africa, and USA, Canada, South Americaand Central America the Middle East

Related manuals

Manual 4 pages 46.1 Kb