Extron electronic MPS 112CS manual Table or wall mounting, Through-desk mounting

Page 11

5.Reliable earthing (grounding) — Maintain reliable grounding of rack- mounted equipment. Pay particular attention to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

Table or wall mounting

The table/wall mounting brackets extend approximately 1/4" (6.4 mm) above the top surface of the switcher enclosure. This design allows for an air space between the enclosure and the surface to which it is mounted. Table or wall mount the switcher as follows:

1.

Attach the table/wall mounting brackets to the switcher with the eight

 

provided #8 machine screws (figure 2-1).

2.

Hold the switcher with the attached brackets against the underside of the

 

table or other furniture, or against the wall. Mark the location of the screw

 

holes of the bracket on the mounting surface.

3.

Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.4 mm) deep in the mounting

 

surface at the marked screw locations.

4.

Insert #8 wood screws into the four pilot holes. Tighten each screw into the

 

mounting surface until just less than 1/4" of the screw’s head protrudes.

5.

Align the mounting screws with the slots in the brackets and place the

 

switcher against the surface, with the screws through the bracket slots.

6.

Slide the switcher slightly forward or back, then tighten all four screws to

 

secure the switcher in place.

Through-desk mounting

Mount the switcher through a desk or podium as follows:

1.

Attach the supplied mounting brackets to the switcher with the machine

 

screws provided (figure 2-1).

2.

Cut the proper sized hole in the mounting surface.

3.

Hold the switcher with the attached brackets against the underside of the

 

table or other furniture. Mark the location of the screw holes of the bracket on

 

the mounting surface.

4.

Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm) deep in the mounting

 

surface at the marked screw locations.

5.

Insert four #8 wood screws through the bracket and into the four pilot holes.

 

Tighten all four screws to secure the switcher in place.

MPS Series • Installation 2-3

Page 10 Page 12
Image 11
Page 10 Page 12
Contents MPS 112 and MPS 112CS Precautions Quick Start MPS Series RS-232 remote connectorConnecting the MPS switcher RS-232 remote connector pinout tableOptimizing the audio Quick Start MPS Series, cont’dTable of Contents Table of Contents, cont’d Introduction OneMPS Series Introduction MPS Series FeaturesIntroduction About the MPS SeriesTwo InstallationRack mounting InstallationMounting the Switcher MPS Series InstallationThrough-desk mounting Table or wall mountingRear Panel Connectors Installation, cont’dConnecting the MPS Switcher Audio input and output Connecting the RCA audio connectorsMicrophone input Connecting the 3.5 mm mini-plugsConnecting the 1/4 6.3 mm microphone connector MPS Remote connection Program audio output MPS 112CSOperation ThreeMicrophone and Program Audio controls Front Panel FeaturesOperation Video/audio group buttonsFront Panel Operation Input selection in Single Switcher modeInput selection in Separate Switcher mode Switcher Mode controlsOperation, cont’d View modeDetermining and selecting the switcher mode Program audio Front panel security lockout Executive modeSingle Switcher mode Separate Switcher modeFollow sub-mode Program audio volumeReset program audio volume Program audio breakawayMicrophone controls Operation, cont’d Windows-based Control Program FourMPS Series Windows-based Control Program Installing the Windows-based Control SoftwareUsing the Software Windows-based Control ProgramMPS Control Program File menu Uploading Firmware UpdatesWindows-based Control Program, cont’d Firmware update confirmation windowProgrammer’s Guide FiveHost-to-MPS Communications Remote Control Port RS-232MPS switcher-initiated messages Programmer’s GuideSymbol definitions Command/Response TableMPS switcher error responses Using the command/response tableProgrammer’s Guide, cont’d Command/response table for SIS commandsMic level Command Ascii Command Response DescriptionSpecial functions Switcher mode selectUploading firmware to the MPS via an SIS command Programmer’s Guide, cont’d Reference Information AAppendix aMPS Series Reference Information SpecificationsReference Information MPS Series Reference Information A-3 SyncAudio program audio Reference Information, cont’dMPS Series Reference Information A-5 Microphone inputIncluded parts Optional accessoriesPart Numbers Cables and connectors Audio cable Part number Pre-cut cables VGA M-M with audio cable Part numberVGA M to BNC M cable Part number Video M-M cable Part numberFCC Class a Notice Extron’s Warranty Extron Electronics, Europe Beeldschermweg 6C
Related manuals
Manual 44 pages 29.11 Kb

MPS 112CS, MPS 112 specifications

Extron Electronics is a recognized leader in professional AV system integration, and its MPS 112 and MPS 112CS are prime examples of their commitment to delivering quality performance and user-friendly interfaces. These Multi-Format Presentation Switchers are designed to enhance the quality and efficiency of presentations in any environment, making them ideal for classrooms, meeting rooms, and other venues.

The MPS 112 is a versatile switcher that can handle various input types, accommodating multiple AV devices. It features a selection of input connectors, including HDMI, VGA, and audio connections, allowing users to seamlessly integrate laptops, document cameras, and other multimedia sources. This multi-format capability ensures that presenters can connect their devices with minimal hassle, fostering a smooth presentation experience.

One of the standout features of the MPS 112 is its built-in scaling technology. This presents a significant advantage by enabling the output resolution to be adjusted according to the capabilities of the display devices connected, ensuring compatibility and optimal visual quality. Furthermore, the device supports automatic input switching, which intelligently selects the active source, simplifying the switching process during presentations.

With the MPS 112CS, Extron has introduced a model equipped with additional functionalities, including integrated audio amplification and support for microphone inputs. This model is designed to be even more user-friendly, catering to environments where audio support is crucial. Its built-in amplifier can drive speakers directly, reducing the need for external audio equipment while maintaining high-quality sound output.

Both models come with Extron’s exclusive Simple Instruction Set (SIS) technology, allowing for quick setup and configuration. This feature ensures that users can manage the switcher effortlessly, decreasing the likelihood of technical difficulties during presentations. Additionally, the MPS 112 and MPS 112CS both come with an intuitive front panel, complete with buttons for source selection and volume control, promoting an accessible user experience.

In terms of build quality, Extron devices are known for their reliability and durability, and the MPS series is no exception. Housed in a robust chassis, these switchers are designed to withstand the rigors of regular use while providing consistent performance.

In conclusion, the Extron MPS 112 and MPS 112CS are sophisticated yet user-friendly AV presentation switchers equipped with essential features for effective multi-source presentations. With their advanced technologies, versatile inputs, and reliable performance, they continue to be valuable assets in professional AV setups.
Top Page Image Contents