Installation and Operation, cont’d
RGB 404 front and rear features
17 18
18 | 17 | 19 | 16 |
VIDEO
INPUT | HIGH Z |
75 Ohm | A | L | R |
| U |
|
|
| D |
|
|
AUTO POWER | I |
|
|
| O |
|
|
|
| PC |
|
NETWORK
H. SHIFT
Extron | RGB 404 |
Yellow
Black
| 1 | CH1L | generatedfrom | CH1L &CH1R | Ground |
| Signal RCA | |||
2 | ||||||||||
| 3 |
|
| |||||||
|
| RCA inputs. | outputs are |
|
|
|
|
| ||
| 4 | CH1R |
|
|
|
|
| |||
5 | REV. A | |||||||||
| 6 |
| generated | CH2L & | ||||||
| 7 |
|
|
|
|
|
| |||
|
| from 3.5 mm inputs. | CH2R outputs are |
|
|
|
|
| ||
| 8 |
| Ground R |
| 3.5 mmL |
|
| |||
9 | CH1R | |||||||||
|
|
| ||||||||
| 10 |
|
|
Red
Green
J12 | J11 |
| J9 |
SW1 J10 | J8 |
2 |
|
1 |
|
ON |
|
J13
1 | = +5V 20 mA max. | 3 2 1 |
| .8V .9V |
| H |
| G |
| |||
2 | = | J13 |
|
| J9 |
|
|
| ||||
3 | = Ground |
|
| RGB 406/ |
|
| B | R | ||||
|
|
|
|
|
| .7V | .8V | V |
| J9 |
| |
SW1 | 1. | ON = Remove | RGB 408 |
|
|
|
| |||||
|
|
| serration pulses. | Captive | .7V | .7V | .9V | CS |
|
|
| |
ON |
| 2. | ON = Digital | Screw | J10 |
| J8 |
| J10 | J8 |
| |
|
| display sync. | Connector |
| 08 99 |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 |
FRONT
1Auto power LED — If active sync pulses are present, power and this LED turn on. If not, power and this LED turn off.
2H. Shift (horizontal shift) control — This controls the horizontal centering. If output is SOG or if DIP
3Input — This
4High Z/75 Ohm switch — For proper video termination, set this switch to 75 Ohms if no local monitor will be connected.
5PC type 3.5 mm stereo audio input connector — This connector is for unbalanced input to audio channel 2. Wire the input plug as shown here.
Tip (+) | Sleeve (GND) |
Ring (R,
Tip (L, +)
Sleeve (GND)
6Left and right audio channel RCA connectors — These connectors are for unbalanced input to audio channel 1. Wire the input plugs as shown below.
Tip Sleeve ()
7Network
8 | 7 | 6 | 5 | 9 | 10 | 11 | 12 | 13 | 14 | 15 |
REAR
8Pin assignment label for the audio output captive screw connector (item 9) — Audio output wiring is discussed in the cabling section of this chapter.
9Audio output captive screw connector — Use this connector for the balanced output from both audio channels (1 and 2). See the wiring diagram label (item 8) and the cabling section in this manual for wiring instructions.
10J13 jumper — Pin 1 = +5V, pin 2 =
11SW1 DIP switches — 1. ON = Removes serration pulses. 2. ON = Enables Digital Display Sync Processing (DDSP).
12J10 blue gain/peaking jumper — Settings are shown on the label located below the circuit board.
13J9 green gain/peaking jumper
14J8 red gain/peaking jumper
15Circuit board — Only key components are shown here.
16
17Composite video
18
19BNC output connectors — These 6 connectors are for video and sync output. Connect the coax cables’ BNC connectors
|
| as shown here for red, green and blue |
H | G | video output, and either separate |
| B | R |
V |
| horizontal and vertical sync or |
CS |
| composite sync. |
|
|
RGB 400 Series Installation and Operation |