Extron electronic PS 1508, PS 910 important safety instructions Mounting, Using the ZipClip

Page 1

Extron External Power Supply •

Installation Guide

2.Fasten the power output cord to the ZipClip base.

a.Insert tie wraps (“zip ties”) along the notches on the side of the power supply and

Important Safety Instructions

This symbol is intended to alert the user of impor- tant operating and maintenance (servicing) instruc- tions in the literature provided with the equipment.

This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product enclosure that may present a risk of electric shock. On the product, risk of shock may be indicated by this symbol.

Read these instructions. Keep these instructions. Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Unplug this device apparatus during lightning storms or when unused for long periods of time.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

This apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNING: This apparatus is a Class I product. This product must be connected to a MAINS socket outlet with a protective earthing connection.

The mains plug is used as the disconnect device and shall remain readily operable.

To prevent the risk of shock, do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards.

WARNING:

Power sources • This equipment should be operated only from

the power source indicated on the product. This equipment is intended to be used with a main power system with a grounded (neutral) conductor. The third (grounding) pin is a safety feature, do not attempt to bypass or disable it.

Power disconnection • To remove power from the equipment

safely, remove all power cords from the rear of the equipment, or the desktop power module (if detachable), or from the power source receptacle (wall plug).

through the tie wrap anchor points on the ZipClip, then around the cord.

b. Connect and pull the

 

Cable

 

Strain

tie wraps until they

Tie Wrap

Relief

are secure. Do not

 

 

over tighten.

 

 

Mounting

CAUTION: These power supplies are not suitable for use in air handling spaces or in wall cavities. The power supply is to be located within the vicinity of the Extron AV equipment in an ordinary location with IEC 1010 pollution degree 2, and secured to an equipment rack within a dedicated closet, podium, or desk.

The installation must be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA 70, article 75 and Canadian Electrical Code part 1, section 16. The power supply shall not be permanently fixed to building or similar structure.

Rack Mounting

About the Extron PS 910, PS 1210, PS 1508 Power Supplies

Model Overview

Model

Power Output

Termination

 

 

 

PS 910C

9 watts, 9 VDC, 1 A

Captive screw

 

 

 

PS 910P

9 watts, 9 VDC, 1 A

DC plug

 

 

 

PS 1210C

12 watts, 12 VDC, 1 A

Captive screw

PS 1210P

12 watts, 12 VDC, 1 A

DC plug

 

 

 

PS 1508C

12 watts, 15 VDC, 0.8 A

Captive screw

ZipClip100

(101-002-01)

 

 

 

 

 

Cabling and Features

Features

Notches for Securing

ACTie Wrap Power

Input

Mounting to a Rack Shelf

These power supplies are one eighth rack wide. Up to eight power supplies can be mounted side by side directly onto a rack shelf.

1.Align the threaded holes in the bottom of the power supply with the holes in an Extron rack

shelf and fasten the supply to the shelf with two 4-40 x 3/16" screws as shown below.

b

RSB 123

Rack Shelf

a

(2) 4-40 x 3/16" Screws

2. Bolt the rack shelf to the rack.

 

Power

50-60Hz X

LED

 

ZipClip

DC Power

Mounting Slot

Output

(front and rear)

Connector Pin Assignments

PS 910C, PS 1210C, PS 1508C

 

PS 910P, PS 1210P

 

Tie Wrap

 

Tip (+)

 

Smooth

 

 

 

 

Power Supply

 

 

 

Output Cord

 

 

 

 

Ridged

Captive Screw

Sleeve (-)

 

 

Connector

 

 

 

Alternative Wiring Option

 

 

 

Smooth

 

 

Power Supply

N/C

 

 

Output Cord

 

 

 

 

 

 

Ridged

 

 

Using the ZipClip 100

Attaching and Removing the Clip and Power Supply

To attach the power supply to the ZipClip 100 mounting clip:

1.Insert the bottom of the power supply down into the clip, starting with one end.

2.Pivot the other end down and press until the clip snaps into place.

To remove the power supply from the ZipClip:

b

1.

Press the tab on the ZipClip.

2.

Pivot the power supply and lift it out

 

 

of the ZipClip.

 

a

Using Tie Wraps for Cable Strain Relief

1.Attach the power supply to the ZipClip mounting clip as described

Mounting to Rack Rails Using a ZipClip

1.Fasten the ZipClip 100 mounting clip to a

rack rail using two rack screws as shown in the diagram at right.

Side of Rack

2. Insert the power supply into the ZipClip as described previously and press to snap it into place.

Inside

Rack

Pole or Table Leg Mounting

1.Wrap a tie wrap around

the projector mount pole or table leg and the power supply at one of the tie wrap notches, and fasten the tie wrap together to secure the power supply to the pole or table leg.

2.Repeat step 1 at the other tie wrap notch.

ZipClip 100

Back of

Rack

Tie Wrap to Pole

previously.

See the next page for

furniture mounting instructions.

1

Image 1
Contents Using the ZipClip About the Extron PS 910, PS 1210, PS 1508 Power SuppliesMounting Furniture Mounting Specifications
Related manuals
Manual 2 pages 40.75 Kb

PS 1210P, PS 1210, PS 1508C, PS 1508, PS 910 specifications

Extron Electronics is renowned for its high-quality audiovisual solutions, and the PS series of power supplies is no exception. The PS 910, PS 1508, PS 1210, PS 1508C, and PS 1210P are specifically designed to provide reliable, robust, and efficient power for a range of A/V components, ensuring optimal performance and longevity.

The PS 910 is a versatile power supply that is known for its compact design and high performance. It delivers a comprehensive output of 9 watts with a regulated voltage, which is essential for sensitive electronic devices. With its sleek and lightweight design, the PS 910 is easy to mount in constrained spaces without compromising on power quality.

The PS 1508 stands out due to its high-efficiency output and unique eight-port distribution system. This power supply features multiple outputs, allowing it to power several devices simultaneously. The built-in surge protection ensures that connected devices are safeguarded against spikes and fluctuations in power, a crucial characteristic for the longevity of A/V equipment.

The PS 1210 offers a balanced approach with a power output of 12 watts. This model is especially beneficial for applications that require consistent and reliable power, such as professional A/V installations. The PS 1210 also incorporates Extron's attention to detail with features like LED indicators that provide status updates, making it user-friendly and efficient in monitoring power supply status.

For environments requiring enhanced protection and versatility, the PS 1508C is ideal. In addition to eight output ports, this model incorporates a metal enclosure, providing additional durability for more demanding settings. It ensures that AV components are not only powered efficiently but also protected from physical damage.

The PS 1210P is designed for professional use, delivering a consistent 12 watts of power with high reliability. Its features include a universal input voltage range, making it adaptable to different power settings worldwide. This makes it an ideal choice for global A/V projects where power configurations may vary.

Overall, the Extron PS series provides a robust solution for powering A/V equipment. With their efficient power distribution, protective features, and user-friendly designs, these power supplies fulfill the needs of various installation environments while promoting the longevity of connected devices. Whether used in commercial installations or educational settings, the PS series stands as a testament to Extron's commitment to quality and innovation in the field of audiovisual technology.