Gigabyte GA-K8VM800M Remove Backup Image Remove backup image. Are you sure? Y/N, Exit and Restart

Page 75

1. Execute Backup Utility:

!Press B to Backup your System or Esc to Exit

The backup utility will automatically scan your system and back up data as a backup image in your hard drive.

Not all systems support access to Xpress Recovery by pressing the F9 key during computer power on. If this is the case, please use the boot from CD-ROM method to enter Xpress

Recovery.

2. Execute Restore Utility:

!This program will recover your system to factory default.

Press R to restore your system back to factory default or press Esc to exit

Restores backup image to original state.

3. Remove Backup Image:

!Remove backup image. Are you sure? (Y/N)

Remove the backup image.

4. Set Password:

!Please input a 4-16 character long password (a-z or 0-9) or press Esc to exit

You can set a password to enter Xpress Recovery to protect your hard disk data. Once this is done, password input will be required to enter Xpress Recovery during the next as well as subsequent system restarts. If you wish to remove the need for password entry, please select "Set Password" and under "New Password/Confirm Password", make sure there is no entry and then press "Enter" to remove password requirement.

5. Exit and Restart:

Exit and restart your computer.

English

- 75 -

Technical Reference

Image 75
Contents GA-K8VM800M Mother Board GA-K8VM800M Read Me First Prepare your computer Installing the motherboard to the chassisTable of Content Table of Content Chapter Introduction Features SummaryBios GA-K8VM800M GA-K8VM800M Motherboard LayoutAlthlonTM ProcessorK8 Block DiagramEnglish Step Hardware Installation ProcessInstall the Central Processing Unit CPU English DDR Install Memory ModulesInstall expansion cards Install I/O Peripherals Cables PS/2 Keyboard and PS/2 Mouse ConnectorUSB/LAN Connector Method1 Audio ConnectorsParallel Port , Serial Port and VGA Port LPT/COMA/VGA Please noteConnectors Introduction ATX ATX Power Connector ATX12V +12V Power ConnectorSysfan System Fan Connector Cpufan CPU Fan ConnectorFDD Floppy Connector Pwrled SATA0 / SATA1 Serial ATA ConnectorFpanel 2 x 10 pins Connector Ramled Faudio Front Audio ConnectorSpdifio Spdif In / Out Connector Surcen Surround Center ConnectorFUSB1 / FUSB2 Front USB Connector Cdin CD In Connector16 I R GAMEGame ConnectorInfolink Comb COM B ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosBattery English English Bios Setup Main Menu Main Menu For example Bios Ver. D8PC Health Status IDE Primary Master, Slave / IDE Secondary Master, Slave Standard Cmos FeaturesDate TimeMemory Floppy 3 Mode Support for Japan AreaDrive a / Dri ve B Halt onAdvanced Bios Features First / Second / Third Boot DevicePassword Check On-Chip IDE Channel1 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel0Onboard FDC Controller Onboard Parallel Port Uart Mode SelectUR2 Dupl ex Mode Paral lel Port ModeAcpi OS Power Management SetupPnP/PCI Configurations Resume by AlarmModem Ring On Case Opened PC Health StatusPCI /AGP FrequencyMhz Frequency/Voltage ControlCPU Host Clock Control CPU Host Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish English Technical Reference @BIOS IntroductionMethod 1 Q-FlashT M Utility Flash Bios Method IntroductionEntering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screen Move to the Bios file you want to flash and press Enter Bios file becomes Fab after updating Your keyboard Exploring the Q-FlashTMutility screen Files found Congratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOS UtilityEnglish 6-Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output ModeNotes Spdif Output Device Optional Device Introduction of audio connectors Jack-Sensing IntroductionAuto-detecting Manual setting Xpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NRAID 1 Mirroring Serial ATA Bios Setting Utility IntroductionRAID Levels RAID 0 StripingEnter Bios Configuration Utility Create Disk Array 74.53 Stripe0 SerialCh1 Master ST9120023AS Delete Disk Array Select Boot ArrayView Array Status View Serial Number of Hard DriveInstalling the RAID drivers Pictures below are shown in Windows XP Install DriversItem Description Software Application Software Information FAQ Long 2 short Monitor or display card error Troubleshooting END Technical Support/RMA Sheet Acronyms Ioapic English Memo USA G.B.T. INC