Gigabyte GA-8VM800M user manual Installation of the Heatsink

Page 13

1-3-2 Installation of the Heatsink

Fig.1

Before installing the heat sink, please first add an even layer of heat sink paste on the surface of the CPU. Install all the heat sink components (Please refer to the heat sink manual for detailed installation instructions).

Fig.2

Please connect the heat sink power connector to the CPU_FAN connec- tor located on the motherboard so that the heat sink can properly function to prevent CPU overheating.

The heat sink may adhere to the CPU as a result of hardening of the heat sink paste. To prevent such an occurrence, it is suggested that either thermal tape rather than heat sink paste be used for heat dissipation or using extreme care when removing the heat sink.

English

- 13 -

Hardware Installation

Image 13

Contents GA-8VM800M Motherboard GA-8VM800M Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8VM800M GA-8VM800M Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your Computer Feature Summary Use of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V/ATX Power Connector FDD FDD Connector Cpufan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector IDE1/IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorSurcen Cdin CD in ConnectorComb Comb Connector FUSB1 / FUSB2 Front USB ConnectorsClrcmos Clear Cmos BAT BatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1a Standard Cmos Features IDE Channel 2/3 Master Floppy 3 Mode Support for Japan AreaDrive a / Drive B Memory Halt onBase Memory Extended MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Integrated PeripheralsLimit Cpuid Max. to Parallel Port Mode On-Chip LAN Boot ROMVIA Onboard LAN USB 1.1 ControllerLegacy USB storage detect Power Management SetupMouse Power On Keyboard Power OnResume by Alarm PME Event Wake UpPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Current CPU TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU FAN Speed RPMFrequency / Voltage Control Dimm OverVoltage Control Dram ClockLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionConfiguring the VT8237VT8237R/VT8237R Plus Sata RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Installing the RAID drivers5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English Taiwan Headquarters Contact UsChina Shanghai