Gigabyte GA-8VM800M user manual Clrcmos Clear Cmos, BAT Battery

Page 25

14)CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily short pins 1-2. To prevent improper use of this header, we do not include a jumper on it.

1

Open: Normal

1

Short: Clear CMOS

English

15) BAT (Battery)

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1.Turn OFF the computer and unplug the power cord.

2.Take out the battery gently and put it aside for about 10 minutes (Or you can use a metal object to connect the positive and negative pins in the battery holder to make them short for one minute).

3.Re-install the battery.

4.Plug the power cord and turn ON the computer.

- 25 -

Hardware Installation

Image 25
Contents GA-8VM800M Motherboard GA-8VM800M Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8VM800M GA-8VM800M Motherboard LayoutBlock Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerFeature Summary Use of licensed Award Bios Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Installation of Expansion Cards I/O Back Panel Introduction English Connectors IntroductionATX12V/ATX Power Connector FDD FDD Connector Cpufan Cooler Fan Power ConnectorSATA0/SATA1 Serial ATA Connector IDE1/IDE2 IDE ConnectorFpanel Front Panel Connector Pwrled Faudio Front Audio Panel ConnectorSurcen Cdin CD in ConnectorComb Comb Connector FUSB1 / FUSB2 Front USB ConnectorsClrcmos Clear Cmos BAT BatteryEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. F1a Standard Cmos Features IDE Channel 2/3 Master Floppy 3 Mode Support for Japan AreaDrive a / Drive B Memory Halt onBase Memory Extended MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Integrated PeripheralsLimit Cpuid Max. to Parallel Port Mode On-Chip LAN Boot ROMVIA Onboard LAN USB 1.1 ControllerLegacy USB storage detect Power Management SetupMouse Power On Keyboard Power OnResume by Alarm PME Event Wake UpPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status Current CPU TemperatureCurrent VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU FAN Speed RPMFrequency / Voltage Control Dimm OverVoltage Control Dram ClockLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Part Two English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish RAID Levels Serial ATA Bios Setting Utility IntroductionConfiguring the VT8237VT8237R/VT8237R Plus Sata RAID Bios Create Array 111.79 Stripe0 SerialCh1 Master ST3120026AS Delete Array Serial Number View Cd bootdrv Menu Installing the RAID drivers5 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Troubleshooting English English English English Taiwan Headquarters Contact UsChina Shanghai