Gigabyte GA-945PLM-(D)S2 user manual Installation of the CPU and CPU Cooler

Page 12

English

1-3 Installation of the CPU and CPU Cooler

Before installing the CPU, please comply with the following conditions:

1. Please make sure that the motherboard supports the CPU.

2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU.

3.Please add an even layer of heat sink paste between the CPU and CPU cooler.

4.Please make sure the CPU cooler is installed on the CPU prior to system use, otherwise overheating and permanent damage of the CPU may occur.

5.Please set the CPU host frequency in accordance with the processor specifications. It is not recommended that the system bus frequency be set beyond hardware specifica- tions since it does not meet the required standards for the peripherals. If you wish to set the frequency beyond the proper specifications, please do so according to your hard- ware specifications including the CPU, graphics card, memory, hard drive, etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:

-CPU: An Intel® Pentium 4 Processor with HT Technology

-Chipset: An Intel® Chipset that supports HT Technology

-BIOS: A BIOS that supports HT Technology and has it enabled

-OS: An operation system that has optimizations for HT Technology

1-3-1 Installation of the CPU

Metal Lever

Fig. 1

Fig. 2

Gently lift the metal

Remove the plastic

 

 

lever located on the

covering on the CPU

 

CPU socket to the

socket.

 

upright position.

 

 

Fig. 3

Fig. 4

 

Notice the small gold

Once the CPU is

 

colored triangle located

properly inserted,

 

on the edge of the CPU

please replace the

 

socket. Align the

load plate and push the

 

indented corner of the

metal lever back into

 

 

its original position.

CPU with the triangle and gently insert the CPU into position. (Grasping the CPU firmly between your thumb and forefinger, carefully place it into the socket in a straight and downwards motion. Avoid twisting or bending motions that might cause damage to the CPU during installation.)

GA-945PLM-(D)S2 (rev. 2.1) Motherboard

- 12 -

Image 12
Contents GA-945PLM-DS2 rev Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers Item Checklist GA-945PLM-DS2/GA-945PLM-S2 rev .1 Motherboard Layout DS2/GA S2-945PLMBlock Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUMbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Line Out Front Speaker OutMIC ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE IDE Connector SATAII0 / 1 / 2 / 3 Sata 3Gb/s Connector, Controlled by ICH7Pwrled Fpanel Front Panel Jumper Faudio Front Audio Connector Cdin CD in ConnectorSpdifio S/PDIF In/Out Connector USB1 / FUSB2 Front USB ConnectorComb Comb Connector Clrcmos Clear CmosCI Chassis Intrusion, Case Open English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For exampleGA-945PLM-DS2 Bios Ver. F1a F12 Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 2, 3 Master/SlaveFloppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password CheckHDD S.M.A.R.T. Capability CPU Hyper-Threading NoteLimit Cpuid Max. to 3 Note No-Execute Memory Protect NoteIntegrated Peripherals Smart LANUSB 2.0 Controller USB Keyboard SupportUSB Mouse Support Legacy USB storage detectSmart LAN LAN Cable Diagnostic Function When LAN Cable Is Functioning NormallyOnboard LAN Boot ROM Parallel Port ModeECP Mode Use DMA Onboard Serial PortPower Management Setup Acpi Suspend TypePower On By Keyboard KB Power on PasswordAC Back Function PnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Mode CPU Smart FAN ControlFrequency/Voltage Control CPU Clock Ratio NoteFSB1066 Core CPU CPU Host Clock ControlPCI Express FrequencyMhz System Memory MultiplierMemory Frequency Mhz Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Install Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings English4 2- / 4- / 6- / 8- Channel Audio Function Introduction Setting Up 4-Channel Audio Setting Up 6-Channel Audio Setting Up 8-Channel Audio Sound Effect Configuration AC97 Audio Configuration Troubleshooting English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System