Gigabyte GA-73PVM-S2H Main Menu, Sample Bios Version F4a, Bios Setup Program Function Keys

Page 37

2-2 The Main Menu

Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use arrow keys to move among the items and press <Enter> to accept or enter a sub-menu.

(Sample BIOS Version: F4a)

CMOS Setup Utility-Copyright (C) 1984-2007 Award Software

`

Standard CMOS Features

Load Fail-Safe Defaults

`

Advanced BIOS Features

Load Optimized Defaults

`

Integrated Peripherals

Set Supervisor Password

`

Power Management Setup

Set User Password

`

PnP/PCI Configurations

Save & Exit Setup

`

PC Health Status

Exit Without Saving

`

MB Intelligent Tweaker(M.I.T.)

 

Esc: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

Time, Date, Hard Disk Type...

BIOS Setup Program Function Keys

< >< >< ><

> Move the selection bar to select an item

<Enter>

Execute command or enter the submenu

<Esc>

Main Menu: Exit the BIOS Setup program

 

 

Submenus: Exit current submenu

 

<Page Up>

Increase the numeric value or make changes

<Page Down>

Decrease the numeric value or make changes

<F1>

Show descriptions of the function keys

<F2>

Move cursor to the Item Help block on the right (submenus only)

<F5>

Restore the previous BIOS settings for the current submenus

<F6>

Load the Fail-Safe BIOS default settings for the current submenus

<F7>

Load the Optimized BIOS default settings for the current submenus

<F8>

Access the Q-Flash utility

<F9>

Display system information

<F10>

Save all the changes and exit the BIOS Setup program

Main Menu Help

The onscreen description of a highlighted setup option is displayed on the bottom line of the Main Menu.

Submenu Help

While in a submenu, press <F1> to display a help screen (General Help) of function keys available for the menu. Press <Esc> to exit the help screen. Help for each item is in the Item Help block on the right side of the submenu.

If you do not find the settings you want in the Main Menu or a submenu, press <Ctrl>+<F1>

to access more advanced options.

When the system is not stable as usual, select the Load Optimized Defaults item to set your system to its defaults.

The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version.

- 37 -

BIOS Setup

Image 37
Contents GA-73PVM-S2H Motherboard Disclaimer CopyrightDocumentation Classifications Identifying Your Motherboard RevisionTable of Contents Regulatory Statements Box Contents GA-73PVM-S2H Motherboard Layout Block Diagram Installation Precautions Hardware InstallationCPU Product Specifications4 Mbit flash Page Installing the CPU Installing the CPU and CPU CoolerCPU Socket Lever Installing the CPU Cooler Installing a Memory Installing the MemoryInstalling an Expansion Card PCI Express x16 Graphics Card Support List Gigabyte GV-RX30HM128D PS/2 Keyboard and PS/2 Mouse Port Back Panel ConnectorsSub Port DVI-D PortUSB Port Optical S/PDIF Out ConnectorIeee 1394a Port ESATA 3Gb/s PortMic In Jack Pink Dual Display ConfigurationsPlayback of HD DVD and Blu-ray Discs IDE Coma SATAII0/1/2 LPT Pwrled Battery Clrcmos Fpanel Internal ConnectorsGND CPUFAN/SYSFAN Fan Headers FDD Floppy Disk Drive ConnectorSATAII0/1/2 Sata 3Gb/s Connectors IDE IDE ConnectorBattery Pwrled System Power LED HeaderFpanel Front Panel Header Faudio Front Panel Audio Header Cdin CD In ConnectorFUSB1/FUSB2/FUSB3 USB Headers, Yellow Spdifio S/PDIF In/Out HeaderComa Serial Port Header 15 F11394 Ieee 1394a Header, GrayCI Chassis Intrusion Header LPT Parallel Port HeaderClrcmos Clearing Cmos Jumper GA-73PVM-S2H Motherboard Bios Setup Startup Screen Following screen may appear when the computer bootsBios Setup Program Function Keys Sample Bios Version F4aMain Menu „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationsTime DateIDE Channel 0 Master/Slave IDE Channel 2/3 Master/SlaveDrive a Floppy 3 Mode SupportHalt on MemoryFirst/Second/Third Boot Device Hard Disk Boot PriorityPassword Check HDD S.M.A.R.T. CapabilityNo-Execute Memory Protect Note Limit Cpuid Max. to 3 NoteCPU Enhanced Halt C1E Note CPU Thermal Monitor 2 TM2 NoteSATA-II RAID Config IDE Prefetch ModeOn-Chip IDE Channel0 NV Serial-ATA ControllerOnboard LAN Boot ROM Onchip Sata ModeSATA-II Pri-Master RAID SATA-II Pri-Slave RAIDWhen No LAN Cable Is Attached Smart LAN LAN Cable Diagnostic FunctionECP Mode Use DMA Parallel Port ModeLegacy USB storage detect Onboard Serial PortModem Ring On PME Event Wake UpUSB Resume from Suspend Power On By Mouse Power-On by AlarmPower On By Keyboard KB Power on PasswordPCI 1 IRQ Assignment PnP/PCI ConfigurationsPCI 2 IRQ Assignment Current System/CPU Temperature Reset Case Open StatusCPU Warning Temperature Case OpenedCPU Smart FAN Control CPU Smart FAN ModeSystem Smart FAN Control MB Intelligent TweakerM.I.T FSB & Memory ConfigFSB-Memory Clock Mode Parameters/ Setting/ Current ValueCurrent CPU Freq, MHz FSB-Memory RatioLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstalling Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationGA-73PVM-S2H Motherboard Before You Begin Xpress Recovery2System Requirements Installing Windows XP and Partitioning the Hard Drive Installation and ConfigurationPage Using the Backup Function in Xpress Recovery2 Accessing Xpress Recovery2Removing the Backup Using the Restore Function in Xpress Recovery2Exiting Xpress Recovery2 Updating the Bios with the Q-Flash Utility Bios Update UtilitiesUpdating the Bios Page Installing and Using @BIOS Updating the Bios with the @BIOS UtilityOptions and Instructions Update the Bios without Using the Internet Update Function EasyTune 5 Interface Button Information Table EasyTuneWindows Vista ReadyBoost Configuring the Onboard Sata Controller Configuring Sata Hard DrivesTo configure Sata hard drives, follow the steps below Installing Sata hard drives in your computerRAID Configuring Sata controller mode in Bios SetupAppendix Configuring RAID set in RAID BiosYES BBS Making a Sata RAID/AHCI Driver Diskette Required for Ahci and RAID ModeInstalling Windows XP Installing the Sata RAID/AHCI Driver and Operating SystemSelect Nvidia nForce Storage Controller and press Enter Enter= Continue R=Repair F3=Exit \Chipset\IDE\Vista\MCP7364\IDE\WinVista64\sataraid Installing Windows Vista NotePage Configuring 2/4/5.1/7.1-Channel Audio Configuring Audio Input and OutputConfiguring Speakers Activating an AC97 Front Panel Audio Module Configuring Sound EffectMuting the Back Panel Audio For HD Audio Only Installing the S/PDIF In and Out Cable Installing the S/PDIF In and Out Cable OptionalPdif Pdif outConfiguring S/PDIF out Configuring Microphone Recording Appendix Recording the Sound Using the Sound RecorderPlaying the Sound Frequently Asked Questions TroubleshootingStart Troubleshooting ProcedureEND Regulatory Notices Weee Symbol StatementOur Commitment to Preserving the Environment China Restriction of Hazardous Substances Table GA-73PVM-S2H Motherboard Appendix GA-73PVM-S2H Motherboard B.T. INC USA Mexico Contact UsGigabyte Global Service System