Troubleshooting
Try these remedies for common Inverter/Charger problems before calling for assistance. Call Tripp Lite Customer Service at (773)
SYMPTOM | PROBLEMS | CORRECTIONS |
No AC Output | Unit is not properly connected to utility power | Connect unit to utility power. |
(All Indicator Lights are OFF) | Operating Mode Switch is set to “DC OFF” and AC input | Set Operating Mode Switch to “AUTO/REMOTE” or “CHARGE ONLY”. |
| is present. |
|
| This is normal when the Operating Mode Switch is set to | No correction is required. AC output will return when AC input |
| “CHARGE ONLY” and AC input is absent. | returns. Set Operating Mode Switch to “AUTO/REMOTE” if you |
|
| require AC output. |
| Output circuit breaker is tripped. | Reset circuit breaker. |
| Unit has shut down due to battery overcharge (preventing | Disconnect any auxiliary chargers. Reset by moving Operating Mode |
| battery damage). The problem may be with connected | Switch to “DC OFF”. Wait 1 minute and switch to “AUTO/REMOTE” or |
| auxiliary chargers, if any, or with the unit’s charger. | “CHARGE ONLY.” If unit remains in shutdown mode after several |
|
| attempts to reset, contact Tripp Lite Customer Service for assistance. |
| Unit has shut down due to excessive battery discharge. | Use an auxiliary charger* to raise battery voltage. Check external |
|
| battery connections and fuse. Unit automatically resets when |
|
| condition is cleared. |
| Unit has shut down due to overload. | Reduce load. Reset by moving Operating Mode Switch to “DC OFF”. |
|
| Wait 1 minute. Switch to “AUTO/REMOTE” or “CHARGE ONLY”. |
Battery Not Recharging | Connected batteries are dead. | Check and replace old batteries. |
(AC Input Present) | Battery fuse* is blown. | Check and replace fuse.* |
| Battery cabling* is loose. | Check and tighten or replace cabling.* |
| Unit has shut down due to battery overcharge (preventing | Disconnect any auxiliary chargers. Reset by moving Operating Mode |
| battery damage). The problem may be with connected | Switch to “DC OFF”. Wait 1 minute and switch to “AUTO/REMOTE” or |
| auxiliary chargers, if any, or with the unit’s charger. | or “CHARGE ONLY.” If unit remains in shutdown mode after several |
|
| attempts to reset, contact Tripp Lite Customer Service for assistance. |
| Charger circuit breaker is tripped. | Reset circuit breaker. |
All Three “BATT VOLT/CHRG CURR” | Battery is excessively discharged. Unit will shut down to | Use an auxiliary charger* to raise battery voltage. Check external |
LEDs are slowly flashing (½ second | prevent battery damage. | battery connections and fuse. Unit automatically resets when |
flashes) with Operating Mode Switch in |
| condition is cleared. |
the “AUTO/REMOTE” position. |
|
|
All Three “BATT VOLT/CHRG CURR” | Battery is overcharged. Unit will shut down to prevent | Disconnect any auxiliary chargers. Reset by moving Operating Mode |
LEDs are rapidly flashing (¼ second | battery damage. The problem may be with connected auxiliary | Switch to “DC OFF”. Wait 1 minute and switch to “AUTO/REMOTE.” |
flashes) with Operating Mode Switch in | chargers, if any, or with the unit’s charger. | If unit remains in shutdown mode after several attempts to reset, |
the “AUTO/REMOTE” position. |
| contact Tripp Lite Customer Service for assistance. |
Red “LOW” Battery Indicator Light is | Battery voltage is low. Unit has shut down | If AC power (utility- or |
flashing with Operating Mode Switch in the | to protect battery from damage. | automatically reset itself and start recharging connected batteries. |
”AUTO/REMOTE” position. |
| However, if an external charger is used to recharge the batteries, |
|
| you will need to manually reset the unit by moving the Operating |
|
| Mode Switch to “DC OFF” for two seconds then returning it to |
|
| “AUTO/REMOTE”. |
| False reading due to undersized or | Use sufficient size DC cable sufficiently connected to |
| insufficiently connected DC cabling. | Inverter/Charger. |
Red “LOAD” Operation | Inverter is overloaded. Unit will automatically shut down | Reduce load. Reset by moving Operating Mode Switch to “DC OFF”. |
Indicator Light flashing | after 5 seconds. | Wait 1 minute. Switch to “AUTO/REMOTE” or “CHARGE ONLY”. |
|
|
|
* |
|
|
Limited Warranty
Tripp Lite warrants its Inverter/Chargers to be free from defects in materials and workmanship for a period of one year (except for outside of U.S.A., Canada and
Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty you must obtain a Returned Material Authorization (RMA) number from Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an authorized Tripp Lite service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been damaged by accident, negligence or misapplication or has been altered or modified in any way, including opening of the unit’s casing for any reason. This warranty applies only to the original purchaser who must have properly registered the product within 10 days of retail purchase.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty to register the warranty of your new Tripp Lite product. You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Note on Labeling Two symbols are used on the labels. V~: AC Voltage V : DC Voltage
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marking name or model number of the product.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
12