Tripp Lite APSX1250F specifications Specifications, System Overview, Output, Input

Supports 230V AC output from a 230V AC line power source or 12V DC battery source

10 millisecond automatic transfer between line and battery power supports UPS protection during blackouts and voltage fluctuations for equipment compatible with a half cycle transfer time

1250W continuous AC output in inverter mode

Double Boost inverter output supports momentary startup loads up to 200% of the continuous rating for up to 10 seconds (see specification chart)

OverPower inverter output supports longer-duration overloads to 150% for 1-60 minutes under ideal battery and temperature conditions. (For best results, utilize OverPower usage for as short a time as possible, ensure that battery bank and cabling are able to provide full nominal DC voltage under load, and allow inverter/charger to fully cool before and after OverPower usage.)

3-stage selectable 7.5/30A battery charger with adjustable settings for wet/gel battery types offers rapid, reliable battery recharging

Protected hardwire bolt-down input lugs safely accept heavy gauge input wiring from attached battery bank

Dual C13 output receptacles pass 120V line power or inverter output through to connected equipment

Reliability-enhanced large-transformer design with secure mounting flanges and protected DC wiring terminals

Moisture-resistant construction enables vehicular or marine operation in high-humidity environments

3-position operating mode switch supports AUTO mode to enable automatic transfer between DC and AC modes, CHARGE-ONLY to maintain a full battery charge when AC is present without auto transfer, and SYSTEM OFF settings

Set of six front panel LEDs display AC/DC operational modes, overload status, DC voltage level, shutdown status and system fault status Set of 4 configuration dip switches support wet/gel battery charging profiles, charger enable/inhibit, and selectable 144/163/182/201V AC low voltage auto transfer during brownouts

Set of 4 additional configuration dip-switches supports 4 levels of charger limiting relative to output load size, a battery equalization program and battery charger low/high settings

Resettable 5A charger AC input breaker, resettable 6A AC output breaker and automatic 2-speed cooling fan protect the inverter from load- and temperature-related failures

Grounding lug properly connects the inverter/charger system to earth ground or vehicle grounding system

Automatic overload and thermal shutoff safely turns off inverter if excessive load or overheating conditions develop

Front panel remote control connector enables remote off/on switching (requires APSRM4 switch accessory). Optional APSRM4 accessory also includes user configurable jacks to support inverter shutoff or startup when a vehicle ignition is engaged

Specifications

OVERVIEW

Intended Application	Emergency Home Power
SYSTEM OVERVIEW
Voltage compatibility	12VDC/230VAC
Frequency	50 Hz
compatibility
OUTPUT
Output watts	INVERTER MODE1250 watts continuous, Double Boost rated to 2500 watts peak (up to 10 seconds). Overpower
	rating supports longer term overloads to 1875 watts for up to 15 seconds prior to inverter shutoff.
Output nominal	230V
voltage
Output voltage	LINE POWER (AC): Maintains 230V nominal sine wave output from line power source. INVERTER POWER (AC):
regulation	Maintains PWM sine wave output voltage of 230 VAC (+/-5%).
Output frequency	50 Hz (+/- 0.3 Hz)
regulation
Outlet quantity / type	Hardwire
Overload protection	Includes 5A input breaker dedicated to the charging system and 6A output breaker for AC output loads
Continuous output	1250
capacity (watts)
Peak output capacity	INVERTER MODE - Double Boost rated to 2500 watts peak (up to 10 seconds). Overpower rating supports longer
(watts)	term overloads to 1875 watts for up to 15 seconds prior to inverter shutoff.
INPUT
Input connection	DC INPUT: Set of 2 DC bolt-down terminals. AC INPUT: IEC-320 C14 inlet connection
type
Input cord length	DC INPUT: User supplies cabling (6 gauge or largersee manual). AC INPUT: IEC-320 C14 inlet, ships with 1.8 m (6
	ft.) IEC C13-C14 AC line cord