Tripp Lite Alternative Power Source owner manual Battery Connection, Standard, DC Vehicular

Page 9

Battery Connection

Standard

1.Connect your APS’s positive DC Terminal directly to a fuse.

UL recommends that you install a recognized UL component fuse block and fuse within 18 inches of the battery. The fuse’s rating must equal or exceed the Minimum DC Fuse Rating listed in your APS model’s specifications on pages 16 or 17.

2.Choose a battery configuration appropriate to your batteries.

•Single Battery Connection: Refer to Diagram 4, page 37. When using a single battery, its voltage must be equal to the voltage of your APS's Inverter Nominal Input Voltage (see specs).

•Parallel Battery Connection: Refer to Diagram 5, page 37. When using multiple batteries in parallel, each battery's voltage must be equal to the voltage of your APS’s Inverter Nominal Input Voltage (see specs).

•Series Battery Connection: Refer to Diagram 6, page 37. When using multiple batteries in series, all batteries must be equal in voltage and amp hour capacity, and the sum of their voltages must be equal to the voltage of your APS's Inverter Nominal Input Voltage (see specs).

3.Use 2/0 gauge wire ONLY to make battery connections. Tighten terminals to a torque of 4 N-m.

Battery connection cable lengths should be short as possible, and must not exceed the Maximum Cable Length listed under Specifications, page 16 or 17. Shorter and heavier gauge cabling limits DC voltage drop and allows for maximum transfer of current.* You must tighten your battery terminals to approximately 4 Newton-meters of torque to create an efficient connection and prevent excessive heating. Insufficiently tightening terminals could void your PowerVerter’s warranty.

*APS models are capable of delivering a much higher wattage output for brief periods of time. Wiring should be configured to handle this brief high-current draw. Though your APS is a high-efficiency converter of electricity, its rated output capacity is limited by the length and gauge of the wires running from the battery to the APS.

DC Vehicular

APS systems may be permanently mounted in a car, truck or boat and connected to draw power from the vehicle's battery. Note: An APS can ONLY be connected to vehicle batteries with voltage that matches the APS’s Nominal DC Input—12V vehicle batteries to 12V Nominal DC Input APS systems, etc. (See Specifications). There are two main ways to make this sort of vehicular battery connection. Choose the Basic Connection if you are running light hand tools or other small appliances for a brief period of time (see Diagram 7, p. 38). Choose the Advanced Connection if you are using your APS to power heavy loads for extended periods of time (see Diagram 8, p. 38). The Advanced Connection incorporates a battery isolator and separate battery system to provide battery power to your APS while preventing it from draining your vehicle’s battery. Note: Depending on your application, you may require more than one Deep Cycle Battery.

Note: The main ground stud on the rear panel must be connected to the vehicle chassis. A non-grounded unit could cause an electrical shock hazard.

Caution: Never operate your APS from an alternator without a battery connected as shown in Diagrams 7 or 8, p. 38.

DC Ground Connection

APS systems must be connected to a grounded, permanent wiring system. For most installations, the negative battery conductor must be bonded to the grounding system at one (and only one) point in the system. All installations must comply with national and local codes and ordinances.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents APS PowerVerter High Efficiency Output IntroductionStage Battery Charger APS Location Warnings Important Safety InstructionConfiguration Dip Switch Settings ConfigurationLoad SHARING/EQUALIZE Battery Charge Battery Charger Limiting PointsSetting Procedure Equalize Battery Charge DIP Switch #3, Group BBattery Selection Selecting Battery TypeSelecting Battery Amp Hour Capacity Standard Battery ConnectionDC Vehicular DC Ground ConnectionAC Connection AC Input Electrical Connection All corded modelsAC Output Electrical Connection All corded models Switches, Indicator Lights & Other Features Set Operating Mode SwitchSwitches Indicator Capacity Indicator LightsOther Features Limited Warranty Maintenance & ServiceMaintenance ServiceSymptom Problems Corrections Inverter Specifications Corded ModelsSpecifications Hardwired Models Manual de Operación Introducción Introducción continua Precauciones Sobre la Conexión de Baterías Precauciones Sobre la Ubicación del APSPrecauciones Sobre la Conexión de Equipos Precauciones de OperaciónSeleccione el Punto Alto de Voltaje de CA ConfiguraciónConfiguración continua Grupo B DE Interruptores DIP Modelos SelectosPuntos Limites del Cargador de Baterias Carga de Baterías Posición del Interruptor Procedimiento de RegulacionSelección de Baterías Seleccione la Capacidad en Amperios/Hora de las BateríasSeleccione el Tipo de Baterías Estándar Conexión de BateríasConexión de Baterías continua Conexión de Baterías DC VehículosConexión de CD a Tierra Conexión de CA Conexión de CA continua Regule el Interruptor Operating Mode Modo de OperaciónInterruptores, Luces Indicadoras y Otras Características InterruptoresLuz Indicadora Capacidad Luces IndicadorasOtras Características Mantenimiento Garantía LimitadaServicio Servicio en MéxicoSimtoma Problemas Solucion Resolucion de ProblemasEspecificaciones Modelos con cable Especificaciones Modelos con toma directa al circuito See Hardwire Electrical Connections, pg Diagrams/EsquemasVolts Basic 12VDC Vehicular Battery Connection. See Pg Corded Model Modelo con Cable Hardwired Model Modelo con Toma Directa al Circuito

Alternative Power Source specifications

Tripp Lite, a leader in power protection, offers a range of alternative power sources designed to meet the diverse needs of users in both residential and commercial settings. Their innovative solutions focus on reliability, performance, and versatility, making Tripp Lite a trusted name for those seeking uninterrupted power supply.

One of the standout products in their lineup is the Tripp Lite UPS (Uninterruptible Power Supply) system, which ensures that critical equipment remains powered during outages. These UPS units typically feature advanced technologies such as Automatic Voltage Regulation (AVR), which corrects minor power fluctuations without switching to battery. This feature helps extend battery life and ensure equipment receives a stable power supply.

Tripp Lite’s UPS models come equipped with a variety of output options, including multiple outlets for connecting devices. Many units also feature USB ports for charging mobile devices or connecting to computers for power management through Tripp Lite’s PowerAlert software. This software provides real-time monitoring and alerts, allowing users to track battery performance and receive notifications about power events.

In addition to UPS systems, Tripp Lite offers portable power stations as alternative energy solutions. These stations are particularly useful for outdoor enthusiasts, contractors, or anyone needing temporary power away from the grid. With features such as pure sine wave output, users can run sensitive electronics without the risk of damage. The battery technology used in these power stations often includes lithium-ion for lightweight portability and enhanced efficiency, ensuring a reliable power supply on the go.

Tripp Lite’s commitment to safety is evident in their products, which include built-in surge protection to guard devices against voltage spikes and electrical surges. Many models are designed with a user-friendly interface, featuring clear display screens that show battery status, load levels, and remaining runtime, making it easy for users to monitor their power situation.

Furthermore, Tripp Lite understands the importance of sustainability. They strive to design their products with energy efficiency in mind, often adhering to stringent environmental standards during production and operation.

In conclusion, Tripp Lite’s alternative power sources embody the features and technologies that businesses and consumers require for reliable power. With innovations like AVR, versatile output options, and user-friendly monitoring systems, Tripp Lite ensures that users can trust their products to provide lasting power solutions in any environment. Whether for home use, office settings, or outdoor adventures, Tripp Lite continues to pave the way in power protection and management.
Top Page Image Contents