Tripp Lite IBRM 12/15A-L20P, IBAR 12/20 Ultra, IBAR12/20 ULTRA, IBAR 1212/20 Ultra Specifications

Page 2

DIAGNOSTIC INDICATOR LIGHTS (IBAR 12 ULTRA, IBAR 12/20 ULTRA & IBRM 8/20A-L20P)

There are three LEDs on the front panel that indicate various operating parameters when the unit is plugged into a live 120VAC/60 Hz outlet as follows, from left to right across the front of the unit:

Protection Present (Green LED)

Indicates the surge-suppression components are intact and providing full protection against spikes and surges. This LED should be lit anytime the IBAR “ON/OFF” switch is turned ON and power is present, as indicated by the lighted power switch. If the Protection Present LED does not light, then some of the surge-suppression components are not functioning and the unit should be returned for repair as soon as possible. You may still use the unit; however, connected equipment will be protected from spikes and surges at a lesser level than normal.

Line Fault (Red LED)

Indicates a wiring fault has been detected. If this LED illuminates at any time the unit is plugged in, the fault should be repaired by a qualified electrician as soon as possible. This LED indicates that phases are reversed, ground is missing or some other sort of wiring error exists in the circuit the IBAR is plugged into. The Line Fault detector circuitry will identify most common wiring faults, but will not necessarily detect every possible type of fault.

NOTE!

If the Line Fault indicator light illuminates, carefully check the AC receptacle the IBAR is plugged into. The receptacle must be tight and securely grounded. A loose AC receptacle may cause the Line Fault LED to illuminate. It must be understood that this Red LED indicates the presence of a wiring fault, but does not indicate the exact nature of the fault. Therefore, a qualified electrician should make necessary repairs.

NOTE!

If the Line Fault indicator light illuminates and power is not present at the outlets, the IBAR’s surge- suppression components have been compromised as a result of surge damage. For service, call Tripp Lite Customer Support at (773) 869-1234. Fully explain the perceived problem to the customer support person. They will either remedy the problem over the phone or give you instructions about return, repair or exchange.

Line “OK” (Green LED)

Indicates 120V AC power is present with no wiring faults detected. When this LED is illuminated, AC power is safe for connected equipment.

SPECIFICATIONS

IBAR 12

IBAR 12 ULTRA

IBAR 12/20 ULTRA

AC Energy Absorption (joules):

750

1200

1200

Surge Suppression (amp spikes)*:

60,000

96,000

96,000

UL 1449 Let-Through Rating:

400V

330V

330V

HF Noise Suppression (@ 1 MHz)

 

 

 

Filter Bank #1:

40 dB

40 dB

80 dB

Filter Bank #2:

80 dB

80 dB

-

AC Receptacles:

2 NEMA 5-15R (front)

2 NEMA 5-15R (front)

2 NEMA 5-15R (front)

 

10 NEMA 5-15R (back)

10 NEMA 5-15R (back)

6 NEMA 5-20R (back)

AC Line Cord:

12’, w/NEMA 5-15P plug

12’, w/NEMA 5-15P plug

12’, w/NEMA 5-15P plug

Circuit Breaker (Resettable):

15 amp

15 amp

20 amp

Dimensions (HxWxD, inches):

1-3/4 x 17-1/2 x 4

1-3/4 x 17-1/2 x 4

1-3/4 x 17-1/2 x 4

Weight (lbs.):

4-1/2

3

5

 

 

 

 

SPECIFICATIONS

IBRM 12/15A-L20P

IBRM 8/20A-L20P

AC Energy Absorption (joules):

1200

1200

Surge Suppression (amp spikes)*:

96,000

96,000

UL 1449 Let-Through Rating:

330V

330V

HF Noise Suppression (@ 1 MHz)

 

 

Filter Bank #1:

40 dB

80 dB

Filter Bank #2:

80 dB

-

AC Receptacles:

2 NEMA 5-15R (front)

2 NEMA 5-15R (front)

 

10 NEMA 5-15R (back)

6 NEMA 5-20R (back)

AC Line Cord:

12’, w/NEMA 5-L20P locking plug

12’, w/NEMA 5-L20P locking plug

Circuit Breaker (Resettable):

15 amp

20 amp

Dimensions (HxWxD, inches):

1-3/4 x 17-1/2 x 4

1-3/4 x 17-1/2 x 4

Weight (lbs.):

4-1/2

5

 

 

 

All Models: Nominal Input Voltage: 120VAC; Input Frequency: 50/60 Hz;

Transient Response Time: Instantaneous (0 ns).**

*Spike protection is provided in all three modes; hot to neutral, hot to ground and neutral to ground.

**Transient amplitude reduction occurs faster than the clamp response of the varistors because of the high rejection rate of the ISOBAR filter networks.

9907030 Isobar Rackmount OM DRAFT.p65 2

7/11/00, 2:22 PM

Image 2
Contents Installation Specifications Front Panels Lifetime Limited Warranty

IBRAM 8/20A-L20P, IBRM 8/20A-L20P, IBAM 12/15A-L20P, IBAR 1212/20 Ultra, IBRM 12/15A-L20P specifications

Tripp Lite is a renowned brand in the power management industry, offering a plethora of innovative and reliable products designed to meet the varying needs of homes and businesses alike. Among its extensive lineup, the Tripp Lite IBAR 1212/20 Ultra, IBAM 12/15A-L20P, IBRAM 8/20A-L20P, IBAR 12/20 Ultra, and IBAR 12/20 ULTRA stand out as exceptional choices for power distribution and management.

The Tripp Lite IBAR 1212/20 Ultra is an advanced power strip designed to provide superior surge protection for sensitive electronic equipment. This model features a robust, durable construction with a 12-outlet design, accommodating various devices simultaneously. Its 20 AMP capacity ensures that even power-hungry equipment can operate efficiently without the risk of overload. The integrated 12-foot power cord provides ample reach, making it convenient for use in larger spaces.

The IBAM 12/15A-L20P is another reliable option focused on delivering high current to multiple devices. With a 12-outlet configuration and a 15-Amp rating, this power strip is ideal for managing power in workshop settings or data centers. The 20-amp plug allows for the connection of high-draw appliances, ensuring maximum performance and safety.

The IBRAM 8/20A-L20P is designed for environments that require a robust power solution without compromising on efficiency. Featuring eight outlets and a 20-amp rating, it effectively channels power to high-demand equipment, facilitating smooth operation. Its heavy-duty construction promotes longevity, making it a favorite for industrial and commercial use.

Both the IBAR 12/20 Ultra and IBAR 12/20 ULTRA models embody Tripp Lite's commitment to quality and dependability. With 12 outlets and a 20-amp rating, these units provide versatile solutions for office setups or server rooms. They include features like keyhole mounts for easy installation, built-in surge protection, and EMI/RFI noise filtering, which enhances equipment performance by reducing electromagnetic interference.

In summary, Tripp Lite's IBAR and IBAM series of power strips combine features such as multiple outlet configurations, high amperage ratings, and robust surge protection, making them suitable for various applications. Their user-friendly designs and reliable technology ensure that both individual users and businesses can confidently manage their power needs, thus enhancing productivity and safeguarding valuable equipment. With Tripp Lite, customers gain trusted performance and peace of mind in their power management solutions.