Tripp Lite B022-016, B020-008-17, B020-016-17 warranty F7 Scan Scan, F8 Log Out Lout

Page 20

F7 Scan (SCAN)

Invoke the Auto Scan Mode by clicking the F7 field or pressing [F7]. This function allows you automatical- ly cycle through available computers at regular intervals so that you can monitor their activity without hav- ing to take the trouble of switching yourself.

•The selection of computers to be included for Auto Scanning is made with the Scan/Skip Mode setting under the F3 SET function (see page 17).

•The amount of time that each Port displays for is set with the Scan Duration setting under the F3 SET function (see page 17). When you want to stop at a particular location, press the [Spacebar] or [Esc] to stop scanning.

•If the scanning stops on an empty port, or one where the computer is attached but is powered Off, the monitor screen will be blank, and the mouse and keyboard will have no effect. After the Scan Duration time is up, the Scan function will move on to the next port.

•As each computer is accessed, an S appears in front of the Port ID display to indicate that it is being accessed under Auto Scan Mode.

•While Auto Scan Mode is in effect, the console will not function. You must exit Auto Scan Mode in order to regain control of the console.

•While in Auto Scan Mode, the scanning can be paused in order to keep the focus on a particular computer either by pressing P, or with a left click of the mouse.

•To exit Auto Scan Mode, press the [Spacebar] or [Esc].

F8 Log Out (LOUT)

Clicking the F8 field or pressing [F8] logs you out of OSD control of the computers, and blanks the Console screen. This is different from simply pressing [Esc] to deactivate the OSD. With this function you must log in again to regain access to the OSD, whereas with [Esc] all you have to do to reenter the OSD is tap the OSD Hotkey.

Note: 1. When you reenter the OSD after logging out, the screen stays blank except for the OSD Main Menu. You must input your pass- word before you can continue.

2.If you reenter the OSD after logging out, and immediately use [Esc] to deactivate the OSD without having selected a port from the OSD menu, a Null Port message displays on the screen.The OSD Hotkey will bring up the Main OSD Screen.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents This package should consist To prevent damage to this unit or to its connected devicesTable of Contents Features Include OverviewSystem Requirements ComputerConsole for B022-016 only CablesFront View of Console KVM Switch IntroductionStation ID LED Front View of B022-016Port LEDs Rear View for B022-016 Installation Single-Station InstallationsMultiple Station Daisy-Chained Installation To set up a daisy-chained installationLCD OSD On-Screen Display Configuration LCD OSD allows you to set up and configure the LCD displayManual Port Switching Basic OperationOpening the Console KVM Closing the Console KVMPort ID Numbering Powering Off and RestartingHot Plugging Port Control Using Hotkeys Invoking the Hotkey ModeHotkeys Selecting the Active PortStarting Auto Scan Setting the Scan IntervalPausing in Auto Scan Skip Mode Hotkey Beeper ControlHotkey Summary Table Port ID EnterOSD Navigation OSD On-Screen Display OperationOSD Overview OSD Main Screen Headings OSD FunctionsHeading Explanation F1 Go To GotoF3 Set Environment SET OSD HotkeyF4 Administrator ADM PasswordF6 Broadcast Mode BRC F5 Skip SKPF7 Scan Scan F8 Log Out LoutBefore You Begin Firmware Upgrade UtilityTo prepare for the firmware upgrade, do the following Starting the Upgrade To upgrade your firmwareFirmware Upgrade Recovery Upgrade SucceededUpgrade Failed OSD Factory Default Settings Setting DefaultAppendix a Computer Connection TableTroubleshooting SpecificationsSymptom Possible Cause Action Function B020-008 B020-016 B022-016Appendix B Clear Log-in InformationAppendix C Appendix DAppendix E FCC Radio/TV Interference NoticeAddendum
Top Page Image Contents