Tripp Lite B060-016-2 owner manual Topology Considerations, Basic Operations

Page 17

Installation (continued)

Topology Considerations

The use of RJ-45 CPU connectors, combined with our Auto Signal Compensation (ASC), allow signals to travel up to 500 feet (150 meters) and still maintain reliability and high video resolution. This allows the B060 Series KVM installation to take advantage of the internal Cat5e and Cat6 wiring built in to most modern commercial buildings.

Note: Although the B060 Series KVM supports legacy CAT5 wiring, the performance and video quality may degrade over longer distances.

Since the data signals are not transmitted in packets, the transmission cannot go through network hubs or switches. Passive components such as patch panels, keystone jacks, patch cables, etc. can be used to channel the traffic.

Basic Operations

Hot Plugging

The B060 Series KVM supports hot plugging—components can be removed and added back into the installa- tion by unplugging their cables from the ports without the need to shut the unit down. In order for hot plugging to work properly, however, the procedures described below must be followed:

Switching Station Positions: On daisy chained installations, you can switch station positions by simply unplugging from the old parent and plugging into a new one.

Hot Plugging Console Ports: Keyboard, monitor, and mouse can all be hot plugged. If you experience a problem after you plug in a new mouse, do a system reset by pressing the reset switch on the B060 Series KVM’s front panel (see p. 4 for details). If this doesn't resolve the problem, restart the computers that have the problem.

Powering Off and Restarting

Powering off the B060 Series KVM does not affect the computers attached to it. When you restart the B060 Series KVM, you will regain control immediately. To replace a B060 Series KVM, simply power it down; unplug the cables; plug them into the new unit; and power the new unit on.

Note: If any of the computers behave strangely after powering off and restarting, or changing a switch, simply restart the computer.

Port Selection

Port Selection is accomplished either by entering Hotkey combinations from the keyboard, or by means of the B060 Series KVM’s OSD (On Screen Display). OSD Operation is discussed in detail in the next chap- ter; Hotkey Port Selection is discussed on p. 27.

Although hotkeys are handy for a single stage installation, we strongly recommend you use the more powerful and versatile OSD - especially for daisy chained, cascaded, and combined installations.

Port ID Numbering

Each CPU port on a B060 Series KVM installation is assigned a unique Port ID. You can access and control any computer on the installation by specifying the Port ID of the port that it is connected to. Depending on where the computer is on the installation, its Port ID will either have two or three parts.

Single Stage and Daisy Chained Installations

For single stage and daisy-chained installations, the Port ID is made up of two parts: a Station Number and a Port Number:

The Station Number - is a two digit number which reflects the switch’s position in the daisy chain sequence. This corresponds to the number displayed on the front panel Station ID LED.

The Port Number - reflects the port on the B060 Series KVM Station that the computer is connected to.

The Station Number precedes the Port Number.

Note: Station numbers from 1 - 9 are padded with a preceding zero, so they become 01 - 09.

For example, a computer attached to Port 12 of Station 6 would have a Port ID of: 06-12.

17

Image 17
Contents NetDirector Matrix KVM Switches This package should include Table of ContentsHardware Requirements FeaturesIntroduction B060 Series Front View B060-032 Shown Console Interface Modules Front View B060 Series Rear View B060-032 ShownConsole Interface Modules O Jack B062-001-PS2B062-001-USB Power JackConsole Interface Modules Rear View Overview InstallationBefore you Begin InterfaceConnect the Server Interface Module to the Computer Single Stage InstallationConnect the Console to the Console Interface Module B062-001-USB USB Cable Connection B062-001-PS2Daisy Chaining Multilevel InstallationsOverview B062-001-USB Cascading B007-008 Protocol Interface CascadingB054-001-PS2 Physical Interface Cascading B022-016 Physical Interface Cascading B062-001-PS2B054-001-PS2 B007-008 B060-032 Daisy Chaining Plus Cascading ExpansionProtocol Interface Expansion B054-001-PS2 B022-016 Physical Interface ExpansionBasic Operations Topology ConsiderationsUser Management and Security Cascaded Protocol Interface InstallationsCascaded Physical Interface Installations OSD Overview OSD OperationOSD Navigation OSD Main Screen HeadingsOSD Functions Heading ExplanationChoice Meaning F1 GotoPort ID F4 ADM Clear the Name List F5 SKP F8 Lout Cascaded OSD OperationHotkey Operation Invoking Hotkey ModeHotkey Port Control Selecting the Active PortInvoking Auto Scan Auto ScanningHotkey Summary Table Skip ModeHotkey Beeper Control Sun Keyboard Emulation Multiplatform SupportMac Keyboard Emulation Introduction Firmware Upgrade UtilityPurpose Before You BeginUpgrade Failure Performing the UpgradeStarting the Upgrade Connection Tables OSD Factory Default SettingsAppendix Clear Login Information Server Interface Modules SpecificationsConsole Interface Modules Warranty Registration TroubleshootingYear Limited Warranty FCC Radio/TV Interference Notice