StarTech.com SV431DDUSB, SV231DDUSB instruction manual Keyboard Hotkey Commands, ScrLk+ScrLk+x

Page 10

Instruction Manual

Keyboard Hotkey Commands

Command Name

Hotkey Sequence

Description

 

 

Switches access to the computer connected to the

Select active computer

[ScrLk]+[ScrLk]+[x]

corresponding port number on the KVM.

 

 

([x]= a number on the keyboard)

 

 

 

 

 

Switches which corresponding port number has access

Select USB hub control

[ScrLk]+[ScrLk]+[Fx]

to the to the devices connected to the KVM’s USB hub.

 

 

([Fx] = Function key: F1=Port 1, F2=Port 2, etc.)

 

 

 

 

 

Switches which port’s speaker and microphone output is

Select Audio/Mic output

[ScrLk]+[ScrLk]+[Fy]

active at the console.

 

 

([Fy] = Function key: F5=Port 1, F6=Port 2, etc.)

Bind computer and USB hub

 

When either the select active computer or select USB

[ScrLk]+[ScrLk]+[Z]

hub control commands are executed, both functions are

control (default)

 

switched to the selected port.

 

 

 

 

 

Unbind computer and USB

 

The computer control and USB hub control can be

[ScrLk]+[ScrLk]+[X]

executed separately; KVM control and USB hub control

hub control

 

control can be assigned to different ports at one time.

 

 

 

 

 

Bind computer and Audio/Mic

 

When either the select active computer or select

[ScrLk]+[ScrLk]+[Q]

audio/mic output control commands are executed, both

control (default)

 

functions are switched to the selected port.

 

 

 

 

 

 

 

The computer control and USB hub control can be

Unbind computer and

[ScrLk]+[ScrLk]+[W]

executed separately; KVM control and Audio/Mic output

Audio/Mic output control

control control can be assigned to different ports at one

 

 

 

time.

Select next/previous port

[ScrLk]+[ScrLk]+[￿, ￿]

Selects the next (up arrow key) or previous (down arrow

 

 

key) numbered port for control.

 

 

 

Select previous port

[ScrLk]+[ScrLk]+[BkSp]

Selects the most recent previously active port.

 

 

 

Beep sound on/off

[ScrLk]+[ScrLk]+[B]

Enables/disables audible responses from the KVM.

 

 

 

Define new hotkey sequence

[ScrLk]+[ScrLk]+[H]+[y]

Change the standard [ScrLk] hotkey to a new value (see

 

 

below).

 

 

 

Auto-scan

[ScrLk]+[ScrLk]+[S]

Automatically switch active ports in sequence every 10

seconds. (Press any key to cancel.)

 

 

 

 

 

Auto-scan with programmable

[ScrLk]+[ScrLk]+[S]+[z]

Auto-scan with a delay other than 10 seconds (see

delay

 

below). Press any key to cancel.

Stop Auto-scan

Press any key on

Terminate Auto-scan activity

keyboard

 

 

Notes:

1.The USB keyboard hotkeys allow you faster and broader control of KVM switching operation, in addition to the front-panel buttons. If you have configured a hotkey preceding sequence other than two consecutive scroll locks, you should change your hotkey sequence accordingly.

2.When the binding of PC & USB hub port control switching is enabled by the hotkey sequence: ScrLk + ScrLk + Z, PC and hub port control switching are bound together. To remove this binding, use the hotkey sequence: ScrLk + ScrLk + X.

3.When the binding of PC, Audio and Mic switching is enabled by the hotkey sequence: ScrLk + ScrLk + Q, any

PC, audio and mic switching are bound together. To remove this binding, use the hotkey sequence: ScrLk + ScrLk + W.

LED Information

Green LED indicates PC port status: solid green – active port; flashing green – PC not connected;

Red LED indicates hub port control status: solid red – that PC has the control of all hub ports.

Important Note: The USB hub control status LED (red) indicates not the connected status of each USB device, but indicates which PC port has the control of all hub ports and their connected devices. For example, when USB LED 1 is lit, it means PC port 1 has the current control of all hub ports and their connected USB devices.

7

Image 10
Contents DVI / VGA USB KVM Switch FCC Compliance Statement Table of Contents Package contents FeaturesIntroduction Hardware Guide InstallationFront Panel Rear panel Operation Installing the KVM Switcher SoftwareHotkey sequence = ScrLk* + ScrLk * + Command keys Front Panel ButtonsSwitch to PC x by Keyboard Hotkeys Switcher SoftwareSwitch to PC x by Operation Menu Hotkey sequence = Ctrl Alt command keyOperation Configuration Menu Dialog Box Using Auto-scanFix Audio to Port KVM Switcher configurationSpecifying Hotkeys Fix Hub Ports to PortKeyboard Hotkey Commands ScrLk+ScrLk+xSpecifications About StarTech.com