Q-Logic 59060-02 B manual A1007.0011 Chap failure, isolating with Invalid Attach

Page 35

A

3 – Event Messages Alarm Events

(A1007.000C) (Security policy restrict mode, security db differs)

Meaning:

The current security policy calls for restrict mode which means that

 

all switches in the fabric must have the same security databases or

 

the ISLs will not login. In this case, the security databases differ.

Action:

Reconfigure the active security set so that the ISL group members

 

are the same.

(A1007.000D) (Security policy in mode mode, other switch in mode mode, sec db conflict)

Meaning:

The security policy on the local switch differs from that of the

 

remote switch.

Action:

Configure the security policy on the remote switch to match that of

 

the local switch.

(A1007.000E) (Security: Auth challenge received from WWN port_WWN, not Authorized to join)

Meaning:

A challenge authentication frame was received from a remote

 

switch, but the local switch does not have an entry for itself within

 

the active security set ISL group.

Action:

Edit the ISL group to include the local switch.

(A1007.000F) (Security: Chap session Gen Response indicates error, chap unable to authenticate)

Meaning:

An Authentication Response frame cannot be built because the

 

CHAP session is not in the right state. The port will isolate.

Action:

Check the remote device for a possible error condition. Reset the

 

port to retry again. If errors continue, disable CHAP for this device

 

if it belongs in the fabric.

(A1007.0010) (Security: Chap session Receive Challenge indicates bad state, chap unable to authenticate)

Meaning:

The CHAP session state is not in the correct state for a Challenge

 

message. Port will isolate.

Action:

Check the remote device for a possible error condition. Reset the

 

port to retry again. If errors continue, disable CHAP for this device

 

if it belongs in the fabric.

(A1007.0011) (Chap failure, isolating with Invalid Attach)

Meaning:

Frame does not match format for a CHAP status frame. Ports will

 

isolate.

Action:

Check the remote device for a possible error condition. Reset the

 

port to retry again. If errors continue, disable CHAP for this device

 

if it belongs in the fabric.

59060-02 B

3-23

Image 35
Contents QLogic Fibre Channel Switch Event Message Guide Document Revision History Table of Contents QLogic Fibre Channel Switch Event Message Guide 59060-02 B Related Materials Intended AudienceTraining Technical SupportAvailability Support Headquarters Contact InformationIntroduction Technical Support 59060-02 B Understanding Severity Levels Displaying Events using the Event BrowserDisplaying the Events Using the Command Line Interface Archiving and Downloading the Event Log Configuring the Event LogConfiguring Port Alarm Thresholds A1000.001E Hotreset failed and the switch is being reset Alarm EventsA1003.0011 Segmenting, zoneset zonesetname already active A1003.000D Fabric already locked by domain domainIDA1003.000E Couldnt acquire lock from domain domainID A1003.0010 Segmenting, zoneset zonesetname not definedA1003.0016 Releasing Lock held too long by domainID A1003.0013 Segmenting, zone zonename merge conflictA1003.0014 Segmenting, alias aliasname merge conflict A1003.0024 Request already in progress internal lock held A1003.0023 Fabric Busy Zoneset operation failedA1003.0025 Error reading security set A1003.002E Zoning merge has been rejected A1003.0030 Zone Merge rejected by remote switchA1003.0031 Error reading zoneset from activate direct A1003.0033 No memory for command completionA1003.0039 Merge failed, total zone limit would be exceeded A1003.0040 Zone Member type membertype unsupported A1003.003C Incompatible Zoning mode, Isolating linkA1003.004F No Zone Merge Response A1003.0050 ISL group does not contain entry for this switchA1003.0054 Failure at remote switch A1004.0009 Eport Isolating due to ESC Incompatibility A1003.0064 UFC failure received from domain domainIDA1004.0008 Eport Isolating due to ELP Incompatibility A1004.000F Eport Isolating due to Merge Zone Failure A1004.000A Eport Isolating due to EFP Domain OverlapA1004.000D Eport Isolating due to RDI SW Reject A1004.000E Eport Isolating due to RDI Domain out of RangeA1004.0015 Eport Isolating due to Invalid Attach A1004.0011 Eport Isolating due to Remote switch isolatedA1004.0012 Eport Isolating due to ISL Security Are not the same on both switches Fabric A1004.0040 A1004.0049 Eport Isolating due to Remote inactive A1004.0052 Eport Isolating due to Switch Binding failureA1004.0048 Eport Isolating due to Port Binding failure A1005.0020 A1005.0013 Hotswap procedure failed must hardreset switchA1005.0039 Fabric Login Flogi from address FCaddress failed A1005.0034 System resource error contact technical supportA1005.0035 System resource error contact technical support A1005.0040 Unsupported SFP within port A1005.003B Warning Debug logging filter level is setA1007.0002 Security WWN deviceWWN not authorized to join A1006.0005 Zoning enforcement error in NameserverA1007.0001 NS Unspecified zoning enforcement error A1007.000B Security Efmd Rejected, bad revision A1007.0011 Chap failure, isolating with Invalid Attach A1007.001C Security Bad Authentication Flags A1007.0025 Security feature not supported Meaning Radius authentication failed Action Event Messages Alarm Events A1007.0037 Device devicewwn failed port binding A1007.0034 Device devicewwn failed switch bindingA1007.0038 Device devicewwn failed switch binding A1007.0033 Device deviceWWN failed port bindingA2001.0002 Pwr1 OK Alarm Cleared A2000.0001 Pwr1 removed Alarm SETA2000.0002 Pwr2 failure Alarm SET A2001.0001 Pwr2 was installed Alarm ClearedSET A3014.0003 Blade bladeID set Down due to blade type mismatch A6001.0004 cmon Blade was removed during Ndcla A6001.0003 cmon switch failed NdclaA6001.0001 cmon insufficient memory A6001.0002 cmon blade failed Ndcla8300.000C Zoning Couldnt acquire lock from domain domainID Switch The switch is proceeding with a hotresetCritical Events 8400.000E Switch Upgrading Licensed Ports to numberofports Switch The switch is now performing a hotresetSwitch The switch will be reset in several seconds Switch The switch will hardreset in several secondsSwitch Invalid user accountname attempted to log into switch Switch New licenses are being installed Switch Upgrading License for 4G capabilitySwitch Upgrading License for multiple ISL capability Switch radius All Radius servers failed to respond 8400.004E Switch ntpdate synchronization lostSwitch Upgrading License for Efcm capability Switch The switch WWN is being upgradedSwitch New firmware has been installed 8400.005D Switch Upgrading License for SANdoctor8400.006A Switch Upgrading License for Fabric Security Downed to due to unavailable licenses will be restarted 8F00000E Link Status status Connection failure, fabric limited to two switches8F00.000D Switch Status status 8F00.000C Fabric Status statusUser Unlock failed, resource unavailable, will retry Switch Attempted unauthenticated login username accountnameUser Releasing Lock held too long by domainID User SFC received with unknown operation operationcodeSwitch that are no longer in use Informative Events Zoning Processing zoning requests, Checkpoint not permitted Mserver Rejecting request commandcommandZoning New Active ZoneSet zonesetname Zoning Removing all inactive zoning objects Zoning Reading zoning database, Checkpoint not permittedSwitch Hotreset not permitted at this time, try again later EPort Port portnumber Inter-Switch Link ISL Offline Switch a CIM edit session has been canceledPortApp Port portnumber Cancelling Online Test EPort In Fabric Reconfiguration8F00.0009 Link Added 8F00.0007 Switch Added8F00.0008 Switch Removed 8F00.000B Login ChangedEvent Messages Informative Events 59060-02 B

59060-02 B specifications

The Q-Logic 59060-02 B is a cutting-edge Fibre Channel host bus adapter (HBA) designed to optimize data transfer rates and enhance connectivity in high-performance computing environments. This advanced HBA is particularly suited for enterprise data centers that demand robust and reliable storage solutions, capable of handling large volumes of data with minimal latency.

One of the main features of the Q-Logic 59060-02 B is its dual-channel architecture, which allows for simultaneous data transfer across two separate Fibre Channel connections. This dual-channel capability effectively doubles the data throughput compared to single-channel adapters, providing seamless scalability for growing storage demands. The HBA supports data rates of up to 2 Gbps, ensuring rapid access to storage devices and enhanced performance for applications requiring high bandwidth.

The Q-Logic 59060-02 B also incorporates advanced technologies that enhance its functionality and performance. One such technology is its integrated hardware acceleration for offloading tasks like error correction and flow control from the host CPU. This offloading conserves system resources, allowing the CPU to focus on other critical tasks and improving overall system efficiency.

In addition, the adapter is designed for easy integration with existing storage networks, thanks to its compliance with SCSI standards and support for various operating systems, including Windows and Linux. This compatibility makes the Q-Logic 59060-02 B a versatile solution for diverse IT environments.

Security is another critical aspect of the Q-Logic 59060-02 B. The adapter includes built-in features for secure data transmission, including advanced encryption capabilities that protect sensitive information traveling across the network. This focus on security helps organizations safeguard their data integrity and comply with industry regulations.

Another noteworthy characteristic of the Q-Logic 59060-02 B is its robustness and reliability. The HBA is designed to handle rigorous data workloads and can operate in demanding conditions typical of data center environments. With its superior quality and performance capabilities, the Q-Logic 59060-02 B remains a preferred choice for enterprises looking to enhance their data storage and retrieval systems while maintaining high levels of performance and security.