Schneider Electric 100BASE-FX Assembly, startup procedure and dismantling, UNPACKING, Checking

Page 5

3.Assembly, startup procedure and dismantling

3.1 UNPACKING, CHECKING

-Check whether the package was delivered complete (see scope of delivery).

-Check the individual parts for transport damage.

Warning

Use only undamaged parts!

3.2 ASSEMBLY

The equipment is delivered in a ready-to-operate condition. The following procedure is appropriate for assembly:

-Check whether the switch factory-setting is suitable for your requirements.

-Pull the terminal block off the Transceiver 100 Mbps TX/FX and wire up the supply voltage and indicator lines.

-Fit the Transceiver 100 Mbps TX/FX on a 35 mm ISO/DIN rail to DIN EN 50 022.

-Suspend the upper snap-in hook of the Transceiver 100 Mbps TX/FX in the ISO/DIN rail, insert a screwdriver horizontally under the housing into the locking slide pull this downwards (see Fig. 6, dismantling) and press the bottom of the module onto the ISO/ DIN rail until it locks in position (Fig. 5).

-Fit the signal lines.

Notes:

-The front panel of the Transceiver 100 Mbps TX/FX is grounded via the separate ground connection in the front panel.

-The shielding ground of the twisted pair lines which can be connected is electrically connected to the front panel.

Fig. 5: Assembling Transceiver 10 Mbps FX/FX

3.3 STARTUP PROCEDURE

You start up the Transceiver 100 Mbps TX/FX by connecting the supply voltage via the 5-pin terminal block. Lock the terminal block with the locking screw at the side.

F/O-Line

For a F/O segment the Transceiver 100 Mbps TX/FX has one port with an SC socket.

The maximum length of an attached F/O segment is:

-3000 m at 50/125 µm fiber type (Transceiver 100 Mbps TX/FX),

-3000 m at 62.5/125 µm fiber type (Transceiver 100 Mbps TX/FX).

TP-Line

For a TP segment the Transceiver 100 Mbps TX/FX has one port with an TP socket.

The maximum length of an attached TP segment is 100 m.

Propagation delay with half duplex segments Using half duplex segments the propagation delay between the terminal devices is 512 bit times (BT) maximum. Add all components of the signal path plus a safety margin.

Propagation delay in the signal path:

Components

Delay

Transceiver 100 Mbps TX/FX

84 BT

Class II Repeater

92 BT

DTE with TP connection

50 BT

DTE with F/O connection

50 BT

Cat. 5 TP cable

1.112 BT/m

F/O cable

1.0 BT/m

Security margin

4 BT

3.4 DISMANTLING

To take the Transceiver 100 Mbps TX/FX off the ISO/DIN rail, insert a screwdriver horizontally under the housing into the locking slide, pull it downwards and tilt the Transceiver 100 Mbps TX/FX upwards (Fig. 6).

Fig. 6: Dismantling

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Order No Ethernet Cabling SystemStaff qualification requirements Safety guidelinesGeneral Specific Functions of the TP Interface Functional descriptionSpecific Functions of the F/O Interface Display ElementsPossibilities of Configuration ConfigurationAssembly Assembly, startup procedure and dismantlingStartup Procedure UNPACKING, CheckingAccessories Technical data General dataNetwork size Transition TP line length TP port ↔ TP port

100BASE-FX, 100BASE-TX specifications

Schneider Electric, a global leader in digital transformation of energy management and automation, offers a variety of networking technologies, including 100BASE-TX and 100BASE-FX. These technologies are foundational in building robust and efficient local area networks (LAN), particularly for industrial applications, commercial enterprises, and smart buildings.

100BASE-TX is an Ethernet standard that operates over twisted-pair cabling, typically utilizing Category 5 or better cabling. This standard supports a data rate of 100 Mbps and has a maximum segment length of 100 meters. One of its main features is its simplicity and cost-effectiveness, enabling easy installation and maintenance. It uses two pairs of wires in the cable: one pair for sending data and the other for receiving. This full-duplex capability allows simultaneous transmission and reception of data, enhancing network efficiency.

100BASE-FX, on the other hand, is designed for fiber-optic networks. It operates over multimode fiber and provides the same 100 Mbps data rate as 100BASE-TX but supports longer cable lengths, up to 2 kilometers (2000 meters). 100BASE-FX includes features that are essential for environments that require high resistance to electromagnetic interference (EMI) and enhanced security. The fiber-optic medium minimizes signal degradation, making it suitable for data transmission over longer distances without loss of integrity.

Both 100BASE-TX and 100BASE-FX incorporate technologies such as auto-negotiation, allowing devices to detect the highest speed and mode available for communication. This compatibility promotes seamless integration between devices, making Schneider Electric's networking solutions versatile and scalable.

The rugged design of Schneider Electric’s networking equipment means that both standards can effectively operate in harsh industrial environments. Their products often feature robust enclosures that resist dust, moisture, and extreme temperatures, ensuring reliable performance over time.

Implementing these technologies enables Schneider Electric to support various applications, from manufacturing automation to smart grid solutions, aligning with the increasing demand for reliable and efficient networking infrastructures. Their 100BASE-TX and 100BASE-FX solutions are pivotal in constructing a more connected, automated, and intelligent world. Native support for these standards facilitates not just connectivity but also innovation in energy management and operational excellence.
Top Page Image Contents