Sun Microsystems 1800 manual CPUset Modules

Page 39

CPUset Modules

CPUset modules have two injector levers which must be operated simultaneously.

As you pull out the CPUset module, the handle in the top panel pops up and must be depressed again manually in order to withdraw the module fully from the chassis (see FIGURE 2-12). Once the handle is clear of the crossbar and has popped up again, it can be used to take the weight of the module.

Caution –CPUset modules are very heavy. The weight warning label on the CPUset is for guidance only. The actual weight of a CPUset depends on its configuration. Both the front and top handles must be used simultaneously once the module has been withdrawn as illustrated in FIGURE 2-12.

On inserting the CPUset module the handle must be depressed in order to push the module fully into the chassis.

Chapter 2 Hardware Installation 25

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Netra ft 1800 Installation Guide Please Recycle Contents Electrical Supply Installation Index Installing and Configuring Sun StorEdge Volume ManagerVi Netra ft 1800 Installation Guide February Figures Circuit Breakers for Dual Power Rails Tables Netra ft 1800 Installation Guide February How This Book Is Organized Who Should Use This BookRelated Books What Typographic Changes MeanTable P-1Typographic conventions Shell Prompts in Command Examples SymbolsTable P-2Shell prompts Sun Welcomes Your Comments Sun Documentation on the WebEnvironmental Considerations Electrical Supply ConsiderationsAirflow Consideration when Mounting in the Equipment Frame DimensionsBefore Installation Minimum 2U 90 mm gap CAF Mounting Requirements 1Mounting Hole Pattern Dimensions LoadingVertical space Depth SafetyTools Unshipping and Mounting the SystemNetra ft 1800 Installation Guide February 1Shipping Brackets and Sacrificial Plinth To Unship and Mount the SystemRefer to Removing and Installing Modules on Mounting Flanges Inch Mountings119-inch Mounting Flange Kit 2Location Matrix For Mounting Flange Screws 19-inch rack 2Support Rail Screw Hole Locations Support Rail and Fixings 19-inch RackChassis Support rail Screw Spacer 619-inch Rack Mounting Flange Kit 323-inch, 24-inch and 600mm Mounting Flange Kits Inch, 24-inch and 600mm Mountings723-inch Rack Mounting Flange Kit 824-inch Rack Mounting Flange Kit 9600-mm Rack Mounting Flange Kit Cable Bracket Assemblies 10Cable Bracket AssemblyModule Injector/Ejector Mechanisms Removing and Installing Modules11Module Injector/ejector Lever To Remove a ModuleCPUset Modules 12Removing a CPUset Module 13Removing a CAF CAF Modules14Removing a PCI Card Carrier PCI ModulesPSU Modules 15Removing a Power SupplySlide the module into its slot but not fully home To Replace a ModuleReplacing an RMM To Remove the RMM16Removing an RMM Module Replacing a Disk Chassis To Replace the RMMTo Remove the Disk Chassis 17Removing a Disk Drive 18Removing a DSK Module To Replace the Disk Chassis19Cable Management Shelf Flexible Module CablingTo Install the Filter Trays Installing the Filter TraysIt is unimportant which way up the trays are fitted External I/O Connections on CAF Module CAF External I/O Connections4Console Connector Pinout System Console Terminal Connections5Console and Modem Port Parameters 6Modem Port Pinout Modem Port Connections7Alarms Port Pinout Alarms Port ConnectionsNetra ft 1800 Installation Guide February System Switch Electrical Supply InstallationDC Source Site Requirements Overcurrent Protection Requirements1Overcurrent Protection Requirements Electrical Supply Installation RTN B Return a 48V supply CB CB RTN B RTN a -48V a -48V B Return B DC Supply and Ground Conductor Required Connection MaterialsTo Connect the Ground Lead Dual Grounding EnvironmentNetra ft 1800 Installation Guide February 4Power Inlet Filter Connecting the Power LeadsStrip 9mm of insulation from boths ends of each power lead To Assemble the Power Inlet and LeadsRefer to Figure Secure the cables using adequate strain relief To Power On the System Powering on the SystemPush the other On system switch on the other CAF front panel Disk Space Requirement Netra ft 1800 Install MediaLocal Installation Installation MethodsNetwork Installation To Install the Software Before You StartEstablish the following Boot the system For local installation, type For network installation, go to the OBP ok prompt and typeInstall the Solaris operating environment 1Suggested Disk Layout Reboot the system by typingInstall the appropriate patches Finishing InstallationSetting up Access to Netra ft 1800 CMS Utilities Setting the Manpath VariableSetenv Manpath $MANPATH/opt/SUNWftm Before You Install Sun StorEdge Volume Manager Installing and Configuring Sun StorEdge Volume ManagerLocate the HDD modules in the list Press q twice to exit cmsconfigInstalling the Volume Manager Software Running the InstallationMounting the CD-ROM Manually Setting up the Volume Manager Environment Setting Default Volume CreationDealing with Stale Boot Disks Enabling Recovery Behavior and Boot Disk Detection Initializing the Volume ManagerSetting up Boot Disks Add the disk to a disk group Setting up Other DisksConfiguring Storage To Add a New DiskBoot Disk Aliases Index Netra ft 1800 Installation Guide February Vxdiskadm, configure disks in Volume Manager Weight Empty chassis, 6 maximum, 2 removable modules

1800 specifications

Sun Microsystems, founded in 1982, unveiled an array of innovative products over the years, among which the Sun-1 workstation and later the Sun-1800 series were significant contributions to the technology landscape. Designed specifically for engineering, graphics, and computing tasks, the Sun-1800 series emerged during a period when workstations were essential for high-performance computing applications.

The Sun-1800 series was powered by the SPARC architecture, which became a hallmark of Sun Microsystems' technological advancement. SPARC, an acronym for Scalable Processor Architecture, allowed the system to achieve high levels of performance and efficiency, positioning it well against competitors in the workstation market. The SPARC processors used in the Sun-1800 series enabled faster computation and multitasking, making it well-suited for scientific applications, computer-aided design (CAD), and complex data analyses.

One of the standout features of the Sun-1800 series was its expansive memory capabilities. Supporting configurations that could house up to 128 megabytes of RAM, the workstations were excellent for handling large datasets that were prevalent in research and corporate environments. This high memory capacity, combined with the efficient use of the SPARC architecture, granted users access to significant computational power, which was crucial for multitasking in complex job environments.

The Sun-1800 series also emphasized networking capabilities, with integrated Ethernet support. This allowed users to seamlessly connect their workstations into local area networks, facilitating collaborative projects and data sharing among teams. The use of the Solaris operating system, which was based on UNIX, also provided a robust and stable environment for enterprise applications, making the Sun-1800 ideal for business-critical applications.

Moreover, the system was designed to support various programming languages and development tools, attracting engineers, scientists, and software developers alike. Sun Microsystems also focused on providing high-quality graphics support, with advanced graphical capabilities that enabled users to engage in advanced visualization tasks, such as 3D modeling.

In summary, the Sun Microsystems 1800 series stands out for its powerful SPARC architecture, impressive memory capacity, integrated networking, and robust graphic capabilities. These characteristics, combined with the reliability of the Solaris operating system, positioned the Sun-1800 as a favored choice among professionals in engineering and scientific fields, shaping the future of workstation computing.
Top Page Image Contents