Sun Microsystems 10GBE XFP manual Declaration of Conformity, Emc

Page 11

 

Declaration of Conformity

Compliance Model Number:

ATLS2XGF

Product Family Name:

Sun x8 Express Dual 10 Gigabit Ethernet Fiber XFP Low Profile Adapter

EMC

USA—FCC Class A

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.This equipment may not cause harmful interference.

2.This equipment must accept any interference that may cause undesired operation.

European Union

This equipment complies with the following requirements of the EMC Directive 89/336/EEC:

As Information Technology Equipment (ITE) Class A per (as applicable):

EN 55022:1994 +A1:1995 +A2:1997

Class A

EN 61000-3-2:2000

Pass

EN 61000-3-3:1995 +A1:2000

Pass

EN 55024:1998 +A1:2001 +A2:2003 Required Limits:

IEC 61000-4-2

4 kV (Direct), 8kV (Air)

IEC 61000-4-3

3

V/m

IEC 61000-4-4

1 kV AC Power Lines, 0.5 kV Signal and DC Power Lines

IEC 61000-4-5

1 kV AC Line-Line and Outdoor Signal Lines, 2 kV AC Line-Gnd, 0.5 kV DC Power Lines

IEC 61000-4-6

3

V

IEC 61000-4-8

1

A/m

IEC 61000-4-11

Pass

Safety

This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:

EC Type Examination Certificates:

 

EN 60950-1:2001, 1st Edition

 

IEC 60950-1:2001, 1st Edition

CB Scheme Certificate No.

Evaluated to all CB Countries

 

UL and cUL/CSA 60950-1:2001, CSA C22.2 No. 60950-00 File:E138989-A82 Vol. 54

FDA DHHS Accession Number (Monitors Only)

Supplementary Information

This equipment was tested and complies with all the requirements for the CE Mark.

This equipment complies with the Restriction of Hazardous Substances (RoHS) directive 2002/95/EC.

/S/

 

 

/S/

 

Dennis P. Symanski

DATE

 

Donald Cameron

DATE

Worldwide Compliance Engineering

 

 

Program Manager/Customer Quality

Sun Microsystems, Inc.

 

 

Sun Microsystems Scotland, Limited

4150 Network Circle, MPK15-102

 

 

Blackness Road, Phase I, Main Bldg.

Santa Clara, CA 95054 U.S.A.

 

 

Springfield, EH49 7LR

 

Tel: 650-786-3255

 

 

Scotland, United Kingdom

 

Fax: 650-786-3723

 

 

Tel: +44 1 506 672 539

Fax: +44 1 506 670 011

xi

Image 11
Contents Sun Dual 10GbE XFP PCI Express Card User’s Guide Please Recycle Contents Configuring the nxge Device Driver Parameters Network ConfigurationConfiguring VLANs Configuring the Jumbo Frames FeatureConfiguring Link Aggregation Index SpecificationsDiagnostic Software Tables Page Figures Sun Dual 10GbE XFP PCI Express Card User’s Guide January EMC Declaration of ConformityXii Sun Dual 10GbE XFP PCI Express Card User’s Guide January How This Document Is Organized PrefaceUsing Unix Commands Typographic Conventions Shell PromptsThird-Party Web Sites Related DocumentationDocumentation, Support, and Training Sun Welcomes Your Comments Page Product Description Product OverviewComponents Hardware and Software Requirements Features Sun Dual 10GbE XFP PCI Express Card User’s Guide January To Download the Driver on a Solaris Platform Installing and Setting Up the DriverFor x86 systems Uncompress the gzipped tar fileUnpack the tar file For Sparc systems, change to the following directory# /usr/sbin/pkgadd -d Select the packages you want to installTo Remove the Driver from a Solaris Platform Verify that the nxge driver is installed on the systemTo discover the driver packages run the pkginfo command To remove the driver packages run the pkgrm command# ifconfig -a grep eth Downloading and Installing the Driver on a Linux PlatformLogin to your system # modprobe nxge # rpm -e nxge-1.0-1 To Remove the Driver From a Linux Platform# ethtool -i eth4 driver nxge version Sun Dual 10GbE XFP PCI Express Card User’s Guide January Installing the Adapter Installing the AdapterTo Install the Adapter Installing the Adapter Sun Dual 10GbE XFP PCI Express Card User’s Guide January Install the optical transceivers Installing an Optical TransceiverTo Install an Optical Transceiver Installing the Adapter Ok show-nets Verifying the Hardware InstallationTo Verify the Hardware Installation Connect the Ethernet cablesOk .properties Ok cd /pci@7c0/pci@0/pci@8/network@0,1Ok device-end Rebooting the SystemOk boot -r Configuring the Network Host Files Network Configuration# grep nxge /etc/pathtoinst # ifconfig nxge0 plumb ip-addressup# cat /etc/hosts Export/root/client-name To Set Up a 10-Gigabit Ethernet Port on a Diskless ClientEdit the hosts file in the diskless client’s root directory Network Configuration Find the root directory of the client system # grep client-name /etc/bootparams# shutdown -i0 -g0 -y Proceed with the Solaris Operating System installationOk boot /pci@7c0/pci@0/pci@8/network@0 Shut down and halt the client system# dladm show-dev Refer the boot-device-order image To Boot Over the Network on Solaris x86 and Linux SystemsSystem should reboot after saving the boot configuration Image pxe-mac-addr Press the F12 key to install the OS from the networkSun Dual 10GbE XFP PCI Express Card User’s Guide January Nxge Hardware and Software Overview Configuring the nxge Device Driver ParametersNoninteractive and Interactive Modes Setting nxge Driver Parameters on a Solaris PlatformSetting Parameters Using the ndd Utility To modify a parameter value, use the -setoption To Specify Parameter Values Using the ndd UtilityTo Specify Device Instances for the ndd Utility Man prtconf Setting Parameters Using the nxge.conf File# ndd /dev/nxge1 name to get/set ? Set the parameters for the nxge devices To Set Driver Parameters Using an nxge.conf FileFollowing parameters can be set using Locate the path names and the associated instance numbersSun Dual 10GbE XFP PCI Express Card User’s Guide January Configuring the nxge Device Driver Parameters Class-opt-ipv4-tcp = 100 class-opt-ipv4-udp = Save the nxge.conf file Tuning for Maximum Performance on a Solaris PlatformReboot the system # reboot -rSet ddimsixalloclimit=1 To Improve Performance on an AMD CPU Based Sun PlatformSet ipipsqueuefanout=1 set ipsqueuesoftring=1 Configuring the nxge Device Driver Parameters To Set Parameters Using the ethtool Utility Setting Parameters on a Linux PlatformConfiguring the nxge Device Driver Parameters Following are some common parameters that can be changed # ethtool -k eth4 # ethtool -C eth4 rx-usecs # ethtool -c eth4# /usr/local/bin/nxgeconfig eth4 get classoptipv4udp # /usr/local/bin/nxgeconfig eth4 getNet.core.netdevmaxbacklog = Tuning for Maximum Performance on a Linux Platform# /usr/local/bin/nxgeconfig eth4 set classoptipv4tcp 0xfe0 Net.ipv4.tcpsack =# sysctl -p /etc/sysctlnxge.conf Set up the sysctl utilityJumbo Frames Overview Configuring the Jumbo Frames FeatureChecking Jumbo Frames Configurations # kstat nxge1 grep rdcpackets To Show the Driver Statistics in a Solaris Environment# kstat Nxge38001 Enabling Jumbo Frames in a Solaris EnvironmentSet the maximum MTU for maximum performance To Check Layer 2 ConfigurationBoot -r # ifconfig nxge mtuEnabling Jumbo Frames in a Linux Environment To Check Layer 3 ConfigurationTo Enable Jumbo Frames in a Linux Environment Ensure that the nxge software is installedSet the MTU for maximum performance # ifconfig ethx mtu# ifconfig eth4 To Show the Driver Statistics in a Linux EnvironmentConfiguring the Jumbo Frames Feature Sun Dual 10GbE XFP PCI Express Card User’s Guide January Overview of Link Aggregation Configuring Link AggregationConfiguring Link Aggregation in a Solaris Environment To Configure Link Aggregation in a Solaris Environment # dladm show-aggr -s Use the dladm show-aggr-scommand to display statistics# ifconfig aggr33 plumb # ifconfig aggr33 192.168.1.1/24 broadcast + up# dladm show-aggr -L Configuring Link Aggregation in a Linux EnvironmentTo Configure Bonding for Multiple nxge Interfaces Load the bonding driverConfigure bond0 interface Sun Dual 10GbE XFP PCI Express Card User’s Guide January Overview of VLANs Configuring VLANsVlan Configuring VLANs in a Solaris Environment 2Ethernet Tag Header Format To Configure Static VLANsEnsure that the nxge module is loaded Configuring VLANs in a Linux EnvironmentTo Configure VLANs in a Linux Environment # ifconfig -aInsert the Vlan module Configure the nxge Vlan eth2 in this example# /sbin/vconfig add eth2 # ifconfig eth2.5 xxx.xxx.xx.xxx upConnectors SpecificationsTable A-1XFP Connector Characteristics Performance SpecificationsPower Requirements Physical CharacteristicsSun Dual 10GbE XFP PCI Express Card User’s Guide January SunVTS Diagnostic Software Diagnostic SoftwareUpdating SunVTS to Recognize the Adapter To Update SunVTS to Recognize the AdapterTo Use the netlbtest Using the SunVTS netlbtestSun Dual 10GbE XFP PCI Express Card User’s Guide January Index SymbolsSun Dual 10GbE XFP PCI Express Card User’s Guide January