Paradyne 6218-I1 manual Important Safety Instructions

Page 3

! Important Safety Instructions

1.Read and follow all warning notices and instructions marked on the product or included in the manual.

2.Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots and openings must not be blocked or covered.

3.Do not allow anything to rest on the power cord and do not locate the product where persons will walk on the power cord.

4.Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.

5.General purpose cables are used with this product for connection to the network. Special cables, which may be required by the regulatory inspection authority for the installation site, are the responsibility of the customer. Use a UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber Line (DSL) network.

6.When installed in the final configuration, the product must comply with the applicable Safety Standards and regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.

7.A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate buildings are interconnected, the voltage potential may cause a hazardous condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action prior to interconnecting the products.

8.Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified power source with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified transformer, with a Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use in the country of installation.

9.In addition, since the equipment is to be used with telecommunications circuits, take the following precautions:

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.

Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

CE Marking

When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Library Technical Manuals CE Declarations of Conformity.

FCC Part 15 Declaration

An FCC Declaration of Conformity may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Support -> Technical Manuals -> Declarations of Conformity.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The authority to operate this equipment is conditioned by the requirement that no modifications will be made to the equipment unless the changes or modifications are expressly approved by the responsible party.

6218-A2-GB23-00

September 2005

B

Image 3
Contents 6218-I1 Wireless Router Copyright 2005 Paradyne Corporation All rights reserved Important Safety Instructions 6218-A2-GB23-00 Canada EMI Notice September Contents Advanced Setup Quick SetupDiagnostics Specifications IndexManagement Contents September About This Guide Document Purpose and Intended AudienceDocument Summary Product-Related Documents Introduction FeaturesSystem Requirements Parts ListFront Panel LEDs Front Panel Label and LEDs Color Function Front PanelRear Panel Rear Panel Labels and Connectors FunctionOverview Hardware Installation PC SetupProcedure Connecting the HardwareHardware Installation LED Indicators This LED Should be Windows Run Dialog Configuring Your ComputerNetwork Connections Windows XP Windows XPLocal Area Connection Properties Windows XP Windows ME WindowsWindows 95 and Windows Windows NT Logging in to Your Router User Name Password CapabilityWeb Interface Home Hardware Installation and PC Setup September Status Summary Device InformationWAN WAN Statistics LAN StatisticsAdsl Statistics ATM StatisticsAdsl BER Test Start Adsl BER TestARP RouteQuick Setup with Auto-Connect Enabled Quick SetupDetecting Available PVC Specifying VPI and VCI Quick Setup with Auto-Connect DisabledPPP Username and Password Device Setup WAN Setup Summary WAN Setup Screen Advanced SetupATM PVC Configuration Screen Add Function ATM PVC ConfigurationConnection Type Screen Connection Type ScreenRemove Function WAN Setup SummaryWAN Setup Reboot Message WAN Setup FinishLAN Setup Local Area Network LAN SetupVirtual Servers NAT10. Virtual Server Add Screen Port Triggering 12. Port Triggering Setup14. Port Triggering List DMZ HostIP Filtering Outgoing FirewallIP Filtering Incoming 18. IP Filtering Incoming Filter SetupFirewall MAC Filtering 20. IP Filtering MAC Filtering Setup22. IP Filtering MAC Filtering Add 23. Port Mapping Port Mapping25. Quality of Service Setup Quality of Service26. Quality of Service Add Screen Routing Default GatewayRouting Static Route 28. Default Gateway Setup30. Static Route Add Routing RIPDynamic DNS DNS Server34. Adding a Dynamic DNS Entry Phone Line Pair Modulation MethodsCapability DSL Advanced SettingsTone Selection 37. Tone SettingsWireless Wireless BasicWireless Security 39. Wireless Security 40. Wireless MAC Filter Wireless MAC FilterWireless Advanced Wireless Bridge43. Wireless Advanced Advanced Setup September Testing the DSL Connection DiagnosticsDiagnostics September Saving and Restoring the Configuration Backing Up Configuration SettingsManagement Backup Settings Upload Confirmation Restore User Settings Screen Restoring Configuration SettingsUpload in Progress Screen Restore Default Settings Screen Restoring Default SettingsSystem Log Restore Default Settings Reboot11. View System Log View System Log12. System Log Configuration Configure System LogSnmp 14. Internet Time Screen Internet TimeAccess Control IP Addresses Access Control Services17. Access Control IP Address Add Screen Access Control Passwords19. Update Software Update Software20. Reboot Router Screen Reboot RouterTable A-1 -I1 Specifications Criteria SpecificationsSpecifications September ATM IndexIN-2 IN-3 IN-4