Patton electronic 1140ARC Configuration Switch SET S2, S2 Summary Table, Rear Card Configuration

Page 5

3.1.2 CONFIGURATION SWITCH SET “S2”

The DIP switches on S2 set word length, extended signaling rate, RTS/CTS delay and V.52 and V.54 diagnostic test. The default settings are summarized in the table below. Following the table is a description of all possible S-2 switch settings.

 

S2 SUMMARY TABLE

 

 

Position

Function

Factory Default

S2-1

Word Length

Off

} 10 bits

S2-2

Word Length

Off

S2-3

Extended Signaling Rate

Off -2.5% to +2.3%

S2-4

RTS/CTS Delay

On

} 7 mS

S2-5

RTS/CTS Delay

On

S2-6

Future Use

-

 

S2-7

Future Use

-

 

S2-8

V.52/V.54 Tests

Off

Enable

 

 

 

 

S2-1 and S2-2: Word Length

Switches S2-1 and S2-2 are set in combination to determine the word length for asynchronous data.

S2-1

S2-2

Setting

Off

On

8 bits

On

On

9 bits

Off

Off

10 bits

On

Off

11 bits

S2-3: Extended Signaling Rate

The setting for switch S2-3 determines the range of variability the Model 1140ARC “looks for” in asynchronous data rates (i.e., the actual variance from a given frequency level the Model 1140ARC will tolerate).

S2-3

Setting

 

Off

-2.5% to +1%

Basic

On

-2.5% to +2.3%

Extended

S2-4 and S2-5: RTS/CTS Delay

The combined settings for switches S2-4 and S2-5 determine the amount of delay between the time the Model 1140ARC “sees” RTS and when it sends CTS. Options are no delay, 7 ms and 53 ms.

S2-4

S2-5

Setting

On

On

7 mS

Off

On

53 mS

On

Off

No delay

Off

Off

No delay

S2-8: V.54 Loopback Test Enable

To reset the V.54 circuit, set switch S2-6 to the “ON” position, then back to the “OFF” position..

S2-8

Setting

Off

V.54

Enable

On

V.54

Disable

3.2 REAR CARD CONFIGURATION

The Model 1140ARC is compatible with two dual-fiber interface cards, one with dual ST connectors and one with dual SMA connectors. Both cards use an HD-26 female for the RS-232 interface. The single configuration jumper (JB1) functions identically on both cards. Figure 3 (below) shows the jumper’s location.

JB1

(pin 1 on right)

3 2 1

Figure 3. Model 1140ARC rear card jumper location

7

8

Image 5
Contents User Manual Service Warranty InformationRadio and TV Interference CE NoticeConfiguration FeaturesFront Card Configuration General InformationS1 Summary Table Configuration Switch SET S1S2 Summary Table Configuration Switch SET S2Rear Card Configuration Rack Power Supply InstallationHOW the Jumper Works DTE Shield Pin 1 & Frgnd JB1Installing the Model 1140ARC Into the Chassis Switching the Power Supply On and OffWiring UP the Model 1140ARC 1 RS-232 ConnectionFiber Connections POWER-UPOperation LED Status MonitorsRemote Digital Loopback RDL Test ModesLocal Analog Loopback LAL Appendix a Patton Model 1140ARC Specifications Using the V.52 BER Test IndependentlyTemperature Range 0-60C32-140F Weight 2 ozPatton Model # Description Appendix B Patton Model 1140ARC Factory Replacement PartsAppendix C Patton Model 1140ARC PIN Configurations Appendix D Block Diagram