3.0 CONFIGURAT I O N
The Model 1012AR is pre-configured at the factory to work in mul- tipoint applications, and in point-to-point applications that use hardware flow control. These are the vast majority of applications that call for the Model 1012AR. Therefore, you will normally have no need to re- configure the Model 1012AR: it will be strictly “plug-and-play”.
The only user-modifiable setting on the Model 1012AR is the RTS control strap. The RTS control strap setting determines how its trans- mitter (i.e. carrier) is activated. When the RST control strap is ON (installed on the pins), the transmitter is enabled by activating RTS (RJ-45 pin 8). This is the factory setting.. When its strap is OFF (removed from the pins), the 1012AR’s transmitter is constantly on. If your application requires the transmitter to be constantly on (i.e. hard- ware flow control disabled), follow the instructions below:
Step 1: Opening the Case. To open the Model 1012AR’s case, insert the blade of a small flat-head screw driver into the narrow slots on either side of the case and twist. The two case halves should pop apart. Then slide the case halves off of the two end inserts. This will expose the PC board.
Step 2: Setting the RTS Strap. On Figure 1 (below), you will see the location of the RTS strap on the PC board. To re-configure the Model 1012AR for transmitter constantly on, remove the strap by pulling it out with a pair of needle-nose pliers or tweezers. Be sure not to lose the strap.
Step 3: Closing the Case. To close the Model 1012AR’s case, be sure the end inserts are in place around th modular jacks (“side”side closest to the clip) and slide th case halves down around them. Then snap the case halves shut.
4.0 INSTA L L AT I O N
The Model 1012AR features modular connectors on both the EIA/TIA-561 and 4-wire (line) sides. The EIA/TIA-561 interface is always a 10 pin RJ-45 jack (although its physical size is identical to an 8-pin RJ-45 jack). A one foot RJ-45 patch cable, wired straight through, is supplied with the unit. The 4-wire interface may be a 6 pin RJ-11 jack or an 8 pin RJ-45 jack.
4.1 CONNECTION TO THE EIA/TIA-561 INTERFACE
The Model 1012AR features a convenient, 10 pin RJ-45 jack for interface with your DTE device. This jack is wired as a DCE accord- ing to the EIA/TIA-561 specification. Figure 2 (below) shows the pins and signals for the modular EIA/TIA-561 interface. Note: Signal are named from the perspective of the DTE (PC/terminal). Therefore, even though pin 7 (below) is called “TD” , the signal is actually incom- ing to the DCE (Model 1012AR).
10 Pin RJ-45 (DCE) | SIGNAL | | | DIRECTION |
1 ---------------------- | N/C | | | | | |
2 ---------------------- | RI | | | | | | | Not Supported |
| | | |
3 ---------------------- | CD | | | | | From 1012AR |
| | | |
4 ---------------------- | DTR | | | | | To 1012AR |
5 ---------------------- | SG | | | | | | | No Direction |
| | | | | |
6 ----------------------RD | | | | | | From 1012AR |
| | | | |
7 ---------------------- | TD | | | | | | | To 1012AR |
| | |
8 ---------------------- | CTS | | | | | From 1012AR |
| | | |
9 ---------------------- | RTS | | | | | To 1012AR |
10 ---------------------- | N/C | | | | | |
. | | | | | | | | | | |
Figure 2. Pin-outs for the Model 1012AR’s | modular EIA/TIA-561 interface jack |
