Patton electronic 1012B Modular Twisted Pair Connection, Signal/Pin Assignments, Signal PIN#

Page 5

Figure 5. Stripping 0.25-inch of insulation from the twisted pairs

3.Connect one pair of wires to XMT+ and XMT- (transmit positive and negative) on the terminal block, making careful note of which color is positive, and which color is negative.

4.Connect the other pair of wires to RCV+ and RCV- (receive positive and negative) on the terminal block, again making careful note of which color is positive, and which color is negative. Your completed crossover cable should be pinned electrically as shown below:

XMT +

RCV+

} One Pair

XMT -

RCV -

RCV -

XMT -

} One Pair

RCV +

XMT+

5.When you finish connecting the wires to the terminal block, the assembly should resemble the diagram Figure 6 below.

Figure 6. Wiring terminal block of Model 1012B

The Model 1012B is now installed.

4.1.2 MODULAR TWISTED PAIR CONNECTION

The Model 1012B offers two interface options for twisted pair connection: RJ-11 (6-wire) jack and RJ-45 (8-wire) jack. Pages 9 and

10 show signal/pin assignments for the jacks, as well as pin-outs for the appropriate twisted pair cable topologies.

7

Signal/Pin Assignments

The 6-wire RJ-11 and 8-wire RJ-45 jack options for the Model 1012B are prewired for a standard TELCO wiring environment. Use the guide below when ordering or constructing twisted pair cables.

RJ-11

SIGNAL

RJ-45

SIGNAL

1

.GND†

1

. .N/C

2

.RCV-

2

.GND†

3

.XMT+

3

.RCV-

4

.XMT-

4

.XMT+

5

.RCV+

5

.XMT-

6

.GND†

6

.RCV+

 

 

7

.GND†

 

 

8

. .N/C

Connection to ground is optional

Crossover Cable Construction

Connection of a 4-wire twisted pair circuit between two or more Model 1012Bs requires a crossover cable as shown in the figures on the following page.

 

 

 

RJ-11

SIGNAL

PIN#

PIN# .

. . . . . . . . . .SIGNAL

GND†

1

6 . .

. . . . . . . . . . .GND†

RCV-

2

4 . . .

. . . . . . . . . . .XMT-

XMT+

3

5 . .

. . . . . . . . . . .RCV+

XMT-

4

2 . . .

. . . . . . . . . . .RCV-

RCV+

5

3 . .

. . . . . . . . . . .XMT+

GND†

6

1 . .

. . . . . . . . . . .GND†

 

 

 

RJ-45

SIGNAL

PIN#

PIN# .

. . . . . . . . . .SIGNAL

GND†

2

7 . .

. . . . . . . . . . .GND†

RCV-

3

5 . . .

. . . . . . . . . . .XMT-

XMT+

4

6 . .

. . . . . . . . . . .RCV+

XMT-

5

3 . . .

. . . . . . . . . . .RCV-

RCV+

6

4 . .

. . . . . . . . . . .XMT+

GND†

7

2 . .

. . . . . . . . . . .GND†

Connection to ground is optional

8

Image 5
Contents Copyright Patton Electronics Company All rights reserved User ManualFeatures ServiceRadio and TV Interference DescriptionDCE DTE Setting the Model 1012B AS DCE or DTEConfiguration HOW to Connect to the Twisted Pair Interface Setting the RTS/CD Carrier Control JumperInstallation Terminal Block Twisted Pair ConnectionSignal Signal/Pin AssignmentsSignal PIN# Modular Twisted Pair ConnectionOptional Connection Dual Modular Jacks EIA RS-232, ITU/CCITT Appendix C Model 1012B Block Diagram