Patton electronic 2703 Connection to the Terminal Device, Connection to the Power Source

Page 8

4.2 CONNECTION TO THE TERMINAL DEVICE

The Model 2703 is wired as a DCE, and–when configured proper- ly–supports communication with a wide variety of terminal (DTE) devices. Compatible interface standards include EIA-530 (RS-422), CCITT X.21 and CCITT V.35.

All interfaces are supported on a female UD-26 connector (a sub- miniature 26-pin “D” connector designated the “alt A” in the EIA-232 Standard). The various physical/electrical connections mentioned above are achieved by changing the Model 2703’s DIP switch settings and attaching different adapter cables.

If you wish to construct your own terminal adapter cable, please consult the pinout diagram in Appendix B. If you wish to purchase a terminal adapter cable specifically designed to work with the Model 2703, please refer to the specific Patton part numbers listed in Appendix C.

4.3 CONNECTION TO THE POWER SOURCE

As described in Section 3.3, the Model 2703 is available with three power supply options: two AC and one DC. The two AC power supply options (Standard and Universal) use a female IEC power cord inter- face, for which Patton can supply various domestic and international power cords. Please refer to Appendix C for specific Patton part num- bers when ordering power cords. The DC power supply option uses a 3-pin terminal strip interface (Note: Please refer to the Model 2703 Service Manual for DC power supply wiring instructions).

5.0 OPERATION

Once the Model 2703 is properly configured and installed, it should operate transparently. This sections describes power-up, read- ing the LED status monitors, and using the built-in loopback test modes.

5.1 POWER-UP

To apply power to the Model 2703, first be sure that you have read Section 3.3, and that the unit has the proper voltage setting and fuse. Failure to do so could result in damage to the unit and connected equipment, and may constitute a fire hazard. Having checked the volt- age setting, plug the AC power cord into both the Model 2703 and the AC outlet. Then Power-up the unit using the rear Power switch. Note: the “Power” LED should glow when power is applied to the unit.

5.2 LED STATUS INDICATORS

The Model 2703 features four front panel LEDs that indicate the status of power, network connection, master clock and loopback test. Figure 6 (below) shows the front panel location of each LED.

Following Figure 6 is a description of each LED’s function.

 

Figure 6. Model 2703 Front Panel

Power

Glows red when the Model 2703 is powered up.

Network

Glows green when the Model 2703 is receiving

 

correctly encoded data from the line interface

 

equipment.

Master Clock

Glows green when the Model 2703 is

 

configured as the master clock unit.

Loop

Glows green when the Model 2703 is in

 

loopback mode.

13

14

Page 7 Page 9
Image 8
Page 7 Page 9
Contents User Manual Service Radio and TV InterferenceCE Notice Tel 301Description FeaturesExternal DIP Switch Settings Switch Set S1 Switches S1-4 and S1-5 Rate AdaptationSwitch S1-6 Data Inversion Switch S1-7 Master/Slave ClockSwitch S1-8 Loopback Test Enable Switch Set S2 To be Used in Conjunction with S1-1Internal Jumper Settings S2 Summary TableJumper Summary Table Power Supply Options SignalConnection to the G.703 Network Twisted Pair 120 OHM ConnectionConnection to the Power Source POWER-UPLED Status Indicators Connection to the Terminal DevicePatton Model 2703 Specifications Loopback Test LALPatton Model 2703 PIN Configurations Factory Parts and AccessoriesPatton Part Number Safety Warnings and RequirementsTerminal DTE Interface Cables

2703 specifications

The Patton Electronic 2703 is a versatile digital to analog converter (DAC) that is designed to enhance audio experiences for both enthusiasts and professionals. This device is renowned for its high performance, delivering an impressive sound quality that meets the demands of various applications, from home audio systems to studio environments.

One of the main features of the Patton Electronic 2703 is its advanced audio processing technology. It utilizes high-resolution audio sampling, supporting formats up to 24-bit/192kHz, which significantly improves the clarity and richness of sound reproduction. This capability allows users to enjoy music with detailed nuances, providing an immersive listening experience.

Another key characteristic of the 2703 is its robust connectivity options. The unit is equipped with multiple input and output options, including USB, optical, and coaxial connections. This flexibility allows it to integrate seamlessly with a wide range of audio sources and devices, making it an ideal choice for users who require versatility in their audio setups.

The design of the Patton Electronic 2703 is both functional and aesthetically pleasing. Its compact form factor makes it easy to incorporate into any audio system without taking up excessive space. Moreover, the device is built to last, featuring high-quality components that ensure longevity and reliability.

In addition to its impressive technical specifications, the 2703 offers user-friendly controls. The front panel includes intuitive buttons for volume adjustment, as well as indicator lights that provide information on the current input signal and operational status. This design consideration ensures that users can easily navigate the device’s features without confusion.

Another significant advantage of the Patton Electronic 2703 is its ability to reduce distortion and enhance signal integrity. This is accomplished through its high-quality digital filters and advanced clock synchronization technology, which minimizes jitter and maintains a clean audio signal.

In conclusion, the Patton Electronic 2703 stands out as a premier choice for anyone seeking a reliable and high-performance digital to analog converter. Its combination of superior sound quality, versatile connectivity, durable construction, and user-friendly design makes it an essential tool for audio professionals and audiophiles alike. Whether you are enhancing your home audio setup or working in a professional studio, the 2703 is engineered to deliver an exceptional audio experience that meets and exceeds expectations.
Top Page Image Contents