Patton electronic 4520 manual Ethernet 10Base-T and 100Base-T, Ethernet cross-over

Page 72

B • Cabling

Model 4520 & 4110 Series Getting Started Guide

 

 

Ethernet 10Base-T and 100Base-T

Ethernet devices (10Base-T/100Base-T) are connected to the SmartNode over a cable with RJ-45 plugs. Use a cross-over cable to a host, or a straight cable to a hub. See figure 30 (host) and figure 31 on page 73 (hub) for the different connections.

Note The SmartNode 4520 Series is equipped with Auto-MDX Ethernet ports.

Use straight-through wired cables for host or hub/switch connections

Figure 30. Ethernet cross-over

72

Ethernet 10Base-T and 100Base-T

Page 71 Page 73
Image 72
Page 71 Page 73
Contents SmartNode 4520 & 4110 Series Mailsupport@patton.com Contents LEDs status and monitoring Cabling Model 4520 & 4110 Series Getting Started Guide Service Compliance informationRadio and TV interference CE noticeCompliance information About this guide AudienceStructure Precautions Safety when working with electricityPreventing electrostatic discharge damage General observationsTypographical conventions used in this document General conventionsChapter contents General informationGeneral information SmartNode Series VoIP routers overview SmartNode Router SmartNode 4524 shownSmartNode 4520 Series router Examples of SN4520 Series rear panelsSmartNode 4520 Series power input connectors Ports descriptions SmartNode 4520 Series front panels SmartNode 4110 Series router Examples of SN4110 Series rear panelsSmartNode 4110 Series power input connectors FXO port. EuroPOTS support Etsi EG201 SmartNode 4110 Series front panels Model 4520 & 4110 Series Getting Started Guide Applications overview Applications overview Introduction Applications for SmartNode 4110 SeriesSIP and H.323 terminal and Pstn gateways Application-ITSP dial-in access Application-Analog line extension over IPApplication-Private line automatic ringdown Plar Application-Enterprise campus BRI to FXS telephony extensionApplications for SmartNode 4520 Series Application-PBX toll bypass gatewayApplication-SOHO off-premise extension Home office networkingApplication-Single-phone Pstn and VoIP access Single-phone accessHardware installation Hardware installation Planning the installation Create a network diagram see section Network information onInstallation checklist Task Verified by DatePower source Site logNetwork information IP related informationInstalling the gateway router Connecting cablesLocation and mounting requirements Mounting the gateway routerAnalog FXS connection Pin Signal Installing the Ethernet cable Model 4520 & 4110 Series Getting Started Guide Connecting to external power source Model 4520 & 4110 Series Getting Started Guide Getting started with the SmartNode Getting started with the SmartNode Steps for setting up a new SmartNode Power connection and default configuration Configure IP addressConnect with the serial interface Login Changing the IP addressConnect the SmartNode to the network Load configurationAdditional information Additional information LEDs status and monitoring LEDs status and monitoring Status LEDs Examples of SN4520 Series front panelsExamples of SN4110 Series front panels Power Model 4520 & 4110 Series Getting Started Guide Contacting Patton for assistance Contacting Patton for assistance Warranty coverage Contact informationReturn for credit policy RMA numbersAppendix a Specifications Specifications Voice processing signalling dependent Voice connectivityConnectivity Fax and modem supportVoice signalling IP servicesVoice routing-session router Dimensions ManagementOperating environment SystemWeight and power dissipation Power supplyAC version Appendix B Cabling Cabling Connecting a serial terminal Serial consoleEthernet 10Base-T and 100Base-T Ethernet cross-overAnalog FXS Ethernet straight-throughConnecting to an FXO line socket Analog FXOAppendix C Port pin-outs Port pin-outs Console port Ethernet 10Base-T and 100Base-T portFXS port FXO port Appendix D SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration SmartNode 4110 Series factory configuration Introduction Appendix E SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration SmartNode 4520 Series factory configuration Introduction Appendix F Installation checklist Installation checklist Installation checklist Introduction
Related manuals
Manual 78 pages 43.34 Kb
Top Page Image Contents