TP-Link TL-WN851ND PIN method, 300Mbps Wireless N PCI Adapter, Enter the PIN from your AP device

Page 19

3.2.2 PIN method

TL-WN851ND

300Mbps Wireless N PCI Adapter

4.When the following window appears, you have successfully connected to the network.

Figure 3-9

3.2.2 PIN method

There are two ways to configure the QSS by PIN method:

1)Enter the PIN from your AP device.

2)Enter a PIN into your AP device.

Following are detailed configuration procedures of each way.

3.2.2.1. Enter the PIN from your AP device

1.Open TWCU and click QSS tab. Select Enter the PIN of my access point or wireless router. In the empty field beside PIN, enter the PIN labeled on the bottom of the router (here takes 13492564 for example). If you have generated a new PIN code for your router, please enter the new one instead. Click Connect to continue.

Figure 3-10

13

Image 19

Contents Rev 1.1.0 TL-WN851ND 300Mbps Wireless N PCI AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCountry CE Mark WarningNational Restrictions 2400.0-2483.5 MHzETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N PCI Adapter Shenzhen, P. R. ChinaCONTENTS 300Mbps Wireless N PCI Adapter 1.1 Package ContentsChapter 1 Product Overview 1.2 IntroductionWorking Status 1.3 Features1.4 Hardware Overview Status2.1 Hardware Installation Chapter 2 Installation2.2 Software Installation TL-WN851ND 5. Click Install to continue the setup 6. The utility and drivers will install. This may take 1~2 minutes TL-WN851ND To connect using QSS Chapter 3 Connect to a Wireless Network3.1 To connect using TWCU To connect using TWCUautomatically connect to your target network next time if you tick Connect automatically 4. You have now successfully connected to your network. Click Close to enjoy the Internet 3.2.1 PBC Push Button Configuration method 3.2 To connect using QSS3. The adapter will be connecting to the target network 3.2.2.1. Enter the PIN from your AP device 3.2.2 PIN method3.2.2.2. Enter a PIN into your AP device 2. The adapter will be connecting to the target networkTL-WN851ND 3.3.1 In Windows 3.3 To connect using Windows built-in wireless utility3.3.2 In Windows Vista 2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect 3.3.3 In Windows XP Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-25 appears to continue 3. The utility will display any available wireless networks in your area. Click on a network displayed using the SSID and click the Connect button 4.1 Profile Chapter 4 ManagementThe following items can be found on the screen 4.1.3 Delete a profile 4.1.2 Modify a profile4.2 Advanced 4.3 About Chapter 5 AP Mode ¾ SoftAP mode Select to enable or disable the function 6.1 Uninstall the utility software from your PC Chapter 6 Uninstall Software6.2 Uninstall the driver software from your PC Normal Appendix A SpecificationsEnvironmental and Physical Appendix B Glossary ¾ Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS