TP-Link TL-WN851ND manual Fcc Statement, FCC RF Radiation Exposure Statement

Page 3

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

Image 3

Contents Rev 1.1.0 TL-WN851ND 300Mbps Wireless N PCI AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCountry CE Mark WarningNational Restrictions 2400.0-2483.5 MHzETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N PCI Adapter Shenzhen, P. R. ChinaCONTENTS 300Mbps Wireless N PCI Adapter 1.1 Package ContentsChapter 1 Product Overview 1.2 IntroductionWorking Status 1.3 Features1.4 Hardware Overview StatusChapter 2 Installation 2.1 Hardware Installation2.2 Software Installation TL-WN851ND 5. Click Install to continue the setup 6. The utility and drivers will install. This may take 1~2 minutes TL-WN851ND To connect using QSS Chapter 3 Connect to a Wireless Network3.1 To connect using TWCU To connect using TWCUautomatically connect to your target network next time if you tick Connect automatically 4. You have now successfully connected to your network. Click Close to enjoy the Internet 3.2.1 PBC Push Button Configuration method 3.2 To connect using QSS3. The adapter will be connecting to the target network 3.2.2.1. Enter the PIN from your AP device 3.2.2 PIN method3.2.2.2. Enter a PIN into your AP device 2. The adapter will be connecting to the target networkTL-WN851ND 3.3.1 In Windows 3.3 To connect using Windows built-in wireless utility3.3.2 In Windows Vista 2. The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect 3.3.3 In Windows XP Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click OK when Figure 3-25 appears to continue 3. The utility will display any available wireless networks in your area. Click on a network displayed using the SSID and click the Connect button 4.1 Profile Chapter 4 ManagementThe following items can be found on the screen 4.1.3 Delete a profile 4.1.2 Modify a profile4.2 Advanced 4.3 About Chapter 5 AP Mode ¾ SoftAP mode Select to enable or disable the function 6.1 Uninstall the utility software from your PC Chapter 6 Uninstall Software6.2 Uninstall the driver software from your PC Appendix A Specifications NormalEnvironmental and Physical Appendix B Glossary ¾ Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS