Polycom DOC2558A manual Replacing a RTM Isdn Card

Page 43

Polycom RMX 2000 Hardware Guide

The blue HS LEDs on the MPM/MPM+/MPMx card and the Control

Unit start flashing and the power on cycle for the card is initiated:

—The card’s resources are added to the system resources list

—The number of available ports on the RMX is increased to the current CFS license level

—Port usage is re-calculated and the Port Gauges and Video/Voice Port Configuration are updated

When the power on cycle of the MPM/MPM+/MPMx card is completed, the blue HS LEDs will turn OFF. The green RDY LED on the MPM/MPM+/MPMx card switches on and remains lit.

Replacing a RTM ISDN Card

The RTM ISDN card can only be used with software version 3.0 or higher.

1Ensure that the power switch on the RMX 2000 is turned OFF (O).

2Loosen the captive screws that fasten the card to the MCU.

3Remove the RTM ISDN card. Use the metal ejector levers to pull the RTM ISDN card out of its slot in the backplane.

4Carefully slide the RTM ISDN card out through the front panel.

5On the card to be installed, move the ejector levers to their fully open position.



		Ejector Lever
			Captive Screw

1-37

Image 43

Contents Polycom RMX System Hardware Guide USA United States Federal Communication Commission FCC Regulatory NoticesChinese Communication Certificate Singapore Certificate Table of Contents Table of Contents Hardware Description Main FeaturesRMX 2000 Specifications Following table summarizes the different system capacities RMX 2000 System CapacitiesSystem Functions MPM Mode MPM+ Mode MPMx Mode MPM+ Resource CapacitiesRack Mount Safety Precautions Safety RequirementsSite Requirements Installation Precautions RMX 2000 Front Panel RMX 2000 ComponentsCntl CPU Component DescriptionComponent Description RTM IP RMX 2000 Rear PanelManagement Network on page G-1 Following items appear on the RMX 2000 rear panelRTM Isdn 3RMX 2000 RTM Isdn Rear Panel Layout ISDN/PSTN Clock SourceCables Connected to the RTM IP & Isdn Cards All external connectors are located on the rear panelComponent RMX 2000 LEDsRMX 2000 Front Panel LEDs Following items appear on the RMX 2000 front panelCard Insertion Initiated If during Card removal Initiated The cardCntl Unit Following LEDs appear on the RTM IP card RMX 2000 Rear Panel LEDsLED Color Description Name ShMG LEDs Function Name Following LEDs appear on the RTM IsdnMPM MPM+ MPM/MPM+ and MPMx Configuration ModesMPM+ Resource Capacities per Card Type MPMx, MPM+ and MPM Modes MPMx Resource Capacities per Card TypeMPMx MPMx Only Operating Mode Selection During Startup / RestartSystem Information Changes AllRemove one MPM card Insert one MPMx card An RMX has two MPM cards installedBoth MPM cards are enabled Inserted MPMx card is enabledInserted MPM card is disabled Remaining MPM card is disabledAn RMX has one MPMx card installed MPMx card is enabledRMX 2000 General Information dialog box opens RMX Chassis TypesComponent Replacement Types of Ejector Levers on RMX Components Using the All Metal Ejector LeverUsing the Modified PMC Compatible Ejector Lever Fully Open The card is released from the MCU housingHandle Replacing the Cntl ModuleHardware Description Replacing the Power Supply Module Replacing the Fan Drawer Removing the MPM/MPM+/MPMx Card from the MCU Replacing a Faulty MPM/MPM+/MPMx CardInstalling the Replacement MPM/MPM+/MPMx Card Installing a New MPM/MPM+/MPMx Card in a Powered On RMXReplacing a RTM Isdn Card PRI Cables Replacing the RTM IP Card