TP-Link TD-8816 manual Fcc Statement, CE Mark Warning

Page 3

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Image 3

Contents Rev2.0.0 1910010536 TD-8816 ADSL2+ Modem RouterCOPYRIGHT & TRADEMARKS CE Mark Warning FCC STATEMENTChapter 3. Quick Installation Guide CONTENTSPackage Contents Hardware Installation4.6.1 Appendix A SpecificationsAppendix B Troubleshooting Appendix C Technical SupportPackage Contents TD-8816ADSL2+ Modem Router User Guide ADSL 1.2 Main FeaturesChapter 1. Introduction 1.1 Product Overview1.3 Conventions Name Chapter 2. Hardware Installation2.1 The Front Panel LED Explanation2.3 Installation Environment 2.4 Connecting the Router2.2 The Back Panel PHONE Connect to the phone sets 3.1 Configure PC Chapter 3. Quick Installation GuideADSL2+ Modem Router User Guide 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? After that, you will see the screen shown below, enter the default User Name admin and the default Password admin, and then click OK to access to the Quick Start screen. You can follow the steps below to complete the Quick Setup Step 5 Click NEXT to finish the Quick Start Chapter 4. Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics ¾ Select Ethernet, and you will see the statistics table as below Statistics Table¾ Select ADSL, and you will see the statistics table as below 4.3 Interface Setup 4.2 Quick Start4.3.1 Internet Virtual Circuit Select the VC number you want to setup, PVC0~PVC7 ¾ TCP MTU Option Enter the TCP MTU as your desire 1. Dynamic IP AddressDirection Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADSL router will only accept but will not send RIP packet. OUT only means the ADSL router will only send but will not accept RIP packet 2. Static IP Address3. PPPoA/PPPoE ADSL2+ Modem Router User Guide 4. Bridge Mode 4.3.2 LANADSL2+ Modem Router User Guide IP Pool Count The max user pool size If you select Disabled, the DHCP function will not take effect 4.4 Advanced Setup 4.4.1 Firewall4.4.2 Routing 4.4.3 NAT ¾ Virtual Circuit Enter Virtual Circuit Index that you plan to setup for the NAT function 4.4.3.1. DMZ4.4.3.2. Virtual Server Other configurations for the entries as shown in Figure To add a virtual server entry4.4.3.3. IP Address Mapping To add a mapping rule IP Address Mapping is only available for VCs with Multiple IPsStep 2 Select the Rule index for the rule as shown in Figure 4.4.4 QoS 4.4.5 VLAN Virtual LAN VLAN is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same wire, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows 1. Assign VLAN PVID for each Interface2. Define VLAN Group 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management4.5.2.1. IP Filter 4.5.2 Filter¾ Interface Select the interface for the entry be shown in the row 2 for the matching with ¾ Rule Type For IP Filter, please select IP hereTo add an IP Address filtering entry 4.5.2.2. MAC Filter Step 5 Finally, click the SAVE to save the entryTo add a MAC Address filtering entry 4.5.2.3. Application Filter Step 4 Finally, click the SAVE to save the entry4.5.2.4. URL Filter ¾ Application Filter Activate or deactivate the function4.5.3 SNMP 4.5.4 UPnPTo add a URL filter entry 4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance4.6.1 Administration 4.6.2 Time Zone1. NTP Server automatically 2. PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items3. Manually To upgrade the routers firmware, follow these instructions below 4.6.3 Firmware4 The router will reboot after the upgrading has been finished To back up the Router’s current settingsTo restore the Router’s settings 4.6.5 Diagnostics 4.6.4 SysRestartTD-8816 ADSL2+ Modem Router User Guide 4.7 Help Appendix A Specifications GeneralPhysical and Environment For Windows XP OS Appendix B Troubleshooting2. What can I do if I don’t know or forgot my password? 3. What can I do if I cannot access the web-based configuration page?Click Network Connections Right-click Local AreaConnection Click Properties Select Obtain DNS server address automatically Double-click InternetProtocol TCP/IP Select Obtain an IP address automatically Click OKADSL2+ Modem Router User Guide For Windows Vista OS Click View network status and tasks Click View statusClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Click View network status and tasks Click Change adapter settings For Windows 7 OSArea Connection Click Properties Select Obtain DNS server address automatically Click Internet Options Select Never dial a connection 4. What can I do if I cannot access the Internet?try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Singapore Appendix C Technical Support Technical SupportGlobal E-mail support@tp-link.com

Related manuals

Manual 73 pages 34.79 Kb

Manual 55 pages 18.54 Kb

Manual 54 pages 55.13 Kb