TP-Link M5350 manual Fcc Statement, FCC RF Radiation Exposure Statement

Page 3
FCC STATEMENT

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user‟s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user‟s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

Image 3
Contents REV 1910100018 M5350 3G Mobile Wi-FiCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTKorea Warning Statements CE Mark WarningCanadian Compliance Statement Industry Canada Statement安全諮詢及注意事項 Safety InformationETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYThe product carries the CE Mark Shennan Rd, Nanshan, Shenzhen, ChinaCONTENTS  Note Package ContentsConventions M5350 3G Mobile Wi-Fi User Guide1.3 Physical Description 1.2 Main FeaturesChapter 1. Introduction 1.1 Product OverviewIndication  OLED ScreenChapter 2. Hardware Installation 2.2 Hardware Installation2.1 Environment Requirements STEP 2 Install the battery  Tips 3.1 System Requirements Chapter 3. Quick Installation Guide3.2 TCP/IP Configuration 3.3 Wireless Connection3.4 Wizard Figure 3-1 Login Window Figure 3-3 Wizard - Dial-up Settings Figure 3-5 Wizard - Finish 4.1 Status Chapter 4. Device Configuration4.2 Wizard 4.3 SMS4.3.1 New Message 4.3.2 Inbox 4.3.3 Outbox 4.3.4 DraftsFigure 4-6 Outbox Figure 4-8 Edit Message Drafts Figure 4-7 Drafts4.3.5 SMS Settings 4.4.1 Dial-up 4.4 Advanced4.4.1.2. Profile Management 4.4.1.1. Dial-upFigure 4-13 Profile Management Figure 4-14 New Profile 4.4.1.3. Network Mode4.4.1.4. PIN Management Figure 4-17 PIN Configuration - PUK Decode 4.4.1.5. Auto-unlock PINFigure 4-18 PIN Code Auto unlock 4.4.2.1. Basic Settings 4.4.2 Wireless4.4.2.2. MAC Filter Figure 4-21 Wireless MAC Filter 4.4.2.3. Wireless Status4.4.3 DHCP Server 4.4.3.1. Basic Settings 4.4.3.2. Client List 4.4.4 System Tools4.4.4.2. Restore Factory 4.4.4.1. Configuration4.4.4.3. Modify Password 4.4.4.4. Reboot 4.4.4.5. About Device T4. How could I restore M5350 to its factory defaults? Appendix A FAQT2. What should I do if I cannot access the Internet? T3. What if I forget my login password?Figure-A-0-2 Figure-A-0-11. Install TCP/IP component Appendix B Configuring the PC Setting IP address manually  Setting IP address automaticallyFigure B-0-4 6 Now click OK to keep your settings Environment Appendix C SpecificationsWireless GeneralAppendix D Glossary