Input Sensitivity Controls

mode. Remember, the 4-ohm minimum load must be connected between the red binding posts. If individual loads were connected to each output (as in normal stereo applications) when the bridge mode is selected. Channel A would supply a normal in-phase signal to its respective load, but Channel B would supply an abnormal out-of-phase signal to its respective load, and both of these signals would contain Channel A source material (Channel B source material, if present, would be defeated). This is a potentially dangerous situation, especially if the individual chan-- nels are being used to supply high and low signals in a typical biamp configuration. Obviously, the speaker components on Channel B would no longer be supplied their intended signal but an out-of-phase version of the Channel A signal, which could easily destroy the associated IOLK- speaker components. To help prevent this, whenever the bridge mode is selected, the standby (“0”) LED and the LED array itself on Channel B is defeated (off), just as if there was some kind of a fault condition present on Channel B. This provides a positive indication that the CS 1000X is no longer in the stereo mode.

TRANSFORMER

CHANNEL B INPUTS

AND SENSITIVITY

CONTROL ARE DEFEATED

RANSFORMER

CONNECT LOAD BETWEEN RED BINDING POSTS 7OVIlOOV LINE

	X-OVER
0	PATCH PANEL (BRIDGE MODE) WITH JUMPERS

The input sensitivity rating of a power amplifier is ,he RMS voltage level required at the input to produce full-rated power into the rated load at the output. This voltage then becomes the level at which the associated mixer must operate in order to drive the amplifier to full output. The

CS 1200X sensitivity controls are calibrated in decibel volts values rather than RMS voltage (usually listed in typical mixer specs), and as such are more useful, since most contemporary mixers employ LED arrays to indicate mixer output levels and are calibrated in decibel volts.

Knowing the power amplifier sensitivity rating in decibel volts will allow the mixer operator to know the status of the power amplifier by noting which LED on the mixer is peaking. Obviously, the LED labeled the same or closest to the sensitivity rating of the power amplifier will indicate full power output of the system. Operation at levels above this rating will cause the power ampli- fier to clip (produce distortion) unless the associated amplifier has a compressor/limiter to mini- mize this distortion. Such a system, called DDT (U.S. Patent #4,3 l&053), is included in the CS 1200X, and the advantages should be obvious. Without DDT, the sound engineer must “ride gain” on the mixer or employ an outboard limiter in order to prevent amp clipping. With DDT the sound man can relax more and enjoy the “ride.” For maximum mixer headroom (which in

CS 1200X specifications

The Peavey CS 1200X is a powerhouse amplifier designed for demanding live sound applications. Known for its robust construction and reliable performance, the CS 1200X has become a popular choice among audio professionals. With a power rating of 1200 watts at 4 ohms, this amplifier delivers ample headroom for driving large speaker systems both in venues and outdoor events.

One of the standout features of the CS 1200X is its innovative Peavey patented technologies, including the DDT speaker protection system. This technology helps to prevent distortion at high volumes, ensuring that audio remains clear and consistent. Additionally, the amp is equipped with a unique Cooler running transistor circuit, designed to dissipate heat effectively and maintain performance during extended use.

The CS 1200X also offers flexible connectivity options. It comes with balanced XLR inputs, as well as 1/4-inch TRS inputs, making it easy to integrate into various audio setups. With both Speakon and binding post outputs, users can connect to a multitude of speakers, further enhancing its versatility. The amplifier features a dual-channel design, allowing independent control over the two channels and providing users with the capability to adjust levels and EQ settings individually.

Notably, the CS 1200X is built to withstand the rigors of life on the road. Its rugged metal chassis is designed to endure the bumps and bruises that come with transport, while the front-mounted cooling fans ensure efficient heat management even in demanding situations. Weighing in at a manageable size, this amplifier strikes a balance between portability and power.

Another appealing characteristic of the CS 1200X is its reliability. Peavey has a long-standing reputation for building equipment that withstands the test of time, and the CS 1200X is no exception. With its high-quality components and solid design, users can expect years of dependable service.

In conclusion, the Peavey CS 1200X is an excellent choice for anyone seeking a powerful and reliable amplifier for live sound applications. With its range of features, including speaker protection technology, flexible connectivity options, and rugged construction, it stands as a testament to Peavey's commitment to performance and quality in the audio industry. Whether for concert venues, DJ setups, or mobile sound reinforcement, the CS 1200X is designed to deliver impressive sound without compromise.