KTI Networks KGS-2401 manual Front Panel, Port Operation, Wiring for 10/100/1000Mbps Copper

Page 8

2.3 The Front Panel

The front panel of the switch is shown as below:

Port Operation

There are 24 * 1000Mbps RJ-45 (copper) ports on the front panel.

The auto-negotiation feature of the switch allows each port of the device running at one of the follow- ing operation modes:

Speed

Duplex Mode

10Mbps

Full Duplex

 

Half Duplex

100Mbps

Full Duplex

 

Half Duplex

1000Mbps

Full Duplex

All ports supports MDI/MDI-X auto crossover capability that is the port can connect either the PC or hub without crossover cable adjustment.

Wiring for 10/100/1000Mbps (Copper)

Following are the summaries of cabling required:

Media

Speed

Wiring

10/100/1000Mbps copper

10Mbps

Category 3,4,5 UTP/STP

 

100Mbps

Category 5 UTP/STP

 

1000Mbps

Category 5,5e UTP/STP

LEDs Definition

The rich diagnostic LEDs on the front panel can provide the operating status of individual port and whole system.

Power LED

This indicator lights green when the switch is receiving power; otherwise, it is

 

off.

 

 

Port LEDs

Every RJ-45 port on the front panel relevant two LEDs (10/100M; 1000Mbps)

 

for indicating the connection speed and activity status.

 

 

-8-

Image 8
Contents Port Gigabit Ethernet Switch KGS-2401 Installation Guide Page Trademarks Table of Contents Factory Default Configuration Unpacking Information General Description Introduction to 24-port Gigabit Web Smart SwitchKey Features Wiring for 10/100/1000Mbps Copper Front PanelPort Operation LEDs DefinitionRear panel of the switch is shown as below Rear PanelRack-mount Installation Installing 24-Port Gigabit Web Smart SwitchDesktop Installation Installing Network Cables Switch-to-Switch ConnectionsNetwork Application Station ConnectionsFunctional Description Access the Switch Factory Default valueWeb Management guide Console Port Out-of-band connectionAggregation QoS Mirror Statistics Discovery After authentication procedure, the home page shows upHome Page System Status & Setting FunctionsAbles timeout. Timeout value in seconds, 0 Status & Settings Functions Better network performance you will have. Default is 1518.Ports Maximum value isThere are 24 entries to set up Vlan EntryTo add new Vlan Entry To remove the Vlan entryEgressTagging Settings FunctionsPort Port Number 1~24 Aggregation/ Trunking Configuration 5 QoSQuality of Service QoS TOS Configuration TOS Value PrecedenceQoS Port Broadcast Storm QoS Port Egress Rate ControlQoS Port Ingress Rate Control Mirror StatisticsDiscovery Auto SearchManual Add RemoveDefault RebootProduct Specifications Command Line Interface Start-up and Terminal configurationLogin/Logout Procedures Command HierarchyHelp Utility Entering Commands Command Description TerminologyMAC Address format hh-hh-hh-hh-hh-hh,hhhhhhhhhhhh or Example 00-00-24-F1-02-03System Commands Console Commands Port CommandsPort Mode Port Flow ControlPort State Port MaxFrameMAC Table Commands Vlan Commands Aggregation/trunking Commands QoS Commands QoS Tosprecedence QoS Egress RateQoS Ingress Rate QoS Storm ControlMirror Commands IP CommandsExample PvidFactory Default Configuration

KGS-2401 specifications

KTI Networks KGS-2401 is a sophisticated gigabit Ethernet switch designed for seamless data distribution in various networking environments. Catering to businesses and workgroups, this switch is built to enhance connectivity, ensuring high performance and reliability.

One of the main features of the KGS-2401 is its 24 Gigabit Ethernet ports, enabling robust data transfer rates of up to 1 Gbps per port. This high throughput is essential for demanding applications such as video streaming, large file transfers, and real-time communications. The switch supports auto-MDI/MDI-X on all ports, simplifying network setup by eliminating the need for crossover cables.

The KGS-2401 employs Store-and-Forward switching technology, which ensures that it only forwards error-free frames to the network. This feature minimizes the chance of collisions and optimizes bandwidth utilization. The switch is equipped with a non-blocking architecture, allowing for the full bandwidth capacity to be utilized on all ports simultaneously, thereby avoiding bottlenecks that can degrade performance.

Another key characteristic is the KGS-2401’s support for Quality of Service (QoS). This allows administrators to prioritize different types of traffic, enhancing the quality of voice and video transmission. By managing data packets, businesses can ensure that critical applications receive the necessary bandwidth while maintaining overall network efficiency.

The KGS-2401 also features extended Layer 2 management capabilities, which include VLAN support and port mirroring. Virtual Local Area Networks facilitate network segmentation, improving security and performance by isolating broadcast domains. Port mirroring is valuable for network monitoring and troubleshooting, providing insights into traffic patterns and potential issues.

On the power front, the KGS-2401 is designed with energy efficiency in mind. It incorporates features like Energy-Efficient Ethernet (IEEE 802.3az) to reduce power consumption during low traffic periods. This not only lowers operational costs but also supports environmentally friendly practices.

In summary, the KTI Networks KGS-2401 is a powerful and flexible gigabit Ethernet switch suited for various networking needs. Its high port density, advanced management features, and commitment to energy efficiency make it an ideal choice for organizations aiming to enhance their network infrastructure while maintaining cost-effectiveness and performance.