Dukane 8755B user manual Replacing the lamp

Page 28

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.)

1	Turn off the projector, and unplug the
1	power cord. Allow the lamp bulb to cool
	for at least 45 minutes, and prepare a
	new lamp.


2	After making sure that the projector has
2	cooled adequately, slowly flip over the

projector, so that the bottom is facing up

5	Insert the new lamp, and tighten the 1
	screw firmly to lock it in place

• Also steadily push the opposite side of the screwed side of the

lamp into the unit.

3 Unscrew the 2 screws, and remove the lamp cover

6	Replace the lamp cover, and tighten
	the 2 screws firmly to lock it in

place

4	Unscrew the 1 screw, and slowly pull
	out the lamp by the handle

• Be careful not to touch the inside of the lamp case.

7	Slowly turn the projector so that
7	the top is facing up


8	Turn on the projector power, and using
8	the menu, reset the lamp timer

• To reset the lamp timer, from the OPTION menu, select LAMP TIME.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

•Do not use with lamp cover removed.

•Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

•When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following operation within 10 minutes of switching power ON.

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp.

26

Image 28

Contents 8755B Page Contents Projector Features Safety InstructionsRemote control Two AA batteries Vol.1/Vol.2Devices you will be using to the projector Only use the power cord that came with the projectorPower cord Part Names ReferenceAuto button Blank button Volume button Mute button RGB button Search button STANDBY/ON buttonVideo button 15 Aspect button Magnify buttons Freeze button Keyboard buttonsSetting UP the Projector Adjusting the Projectors Elevator FeetScreen Adjusting the Screen Size and Projection DistanceTop view Side view Connecting Your Devices Ports and Cables Function Projector Port Connection CablesConnecting Your Devices Connecting to a ComputerConnecting to a DVD Player Connecting to a VCRConnecting to a Display Monitor Putting batteries into the remote control unit Using the Remote ControlOperating the remote control Turning on the Power Selecting an Input Signal Turning OFF the Power Adjusting the Volume Press the Volume buttonPress Buttons to adjust Volume Temporarily Muting the SoundUse Buttons to adjust Position Adjusting the PositionPress the Position button Using the Automatic Adjustment Feature Automatic Adjustment for RGB InputAutomatic Adjustment for Video Input Press the Auto buttonCorrecting Keystone Distortions Press the Keystone buttonAs illustrated on the right, a dialog will appear On the screen to aid you in correcting the distortionUsing the Magnify Feature Freezing the ScreenSelecting the Aspect Ratio Signal SearchingTemporarily Blanking the Screen Using the Menu Functions Select a menu using Buttons Then press Or Enter buttonSelect an item using Buttons, then press Or Enter button Press Buttons to adjust the levelAvailable Functions Remote Control Operation Operating the PC ScreenLamp High Voltage High Temperature High PressureDo not use the projector with the lamp cover removed Replacing the lamp AIR Filter Caring for the air filterReplacing the air filter Caring for the cabinet and remote control transmitter Other CareCaring for the inside of the projector Caring for the lensPage Signal Connector PIN Assignment Signal Terminal SpecificationRGB in 1/2 Sub 15-pin ShrinkExample of Computer Signal Resolution FH kHz FV Hz Rating Signal mode Display modeInitial SET Signals Connection to the Mouse Control ADB MouseUSB Mouse PS/2 MouseCommand data Consist of header 7 bytes + command data 6 bytesRS-232C Communication ProtocolRequesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandCommand data chart 日本語Be EF BA D2 Be EF FD D3 Be EF Ntsc PAL For Technical see the end of this manual Main Menu Multifunctional SettingsMain Menu Picture 1 Menu Picture 2 MenuPICTURE1 Menu PICTURE2 MenuInput Menu Input MenuAuto VideoScreen Menu Screen MenuBlank Start UPOption Menu Option MenuRelated Messages Regarding the Indicator Lamps Power Lamp TempPhenomena That May Easily Be Mistaken for Machine Defects Vol.2-2Vol.2-3 Vol.2-6Specifications Dimension DiagramSpecification Unit mmWarranty and AFTER-SERVICE Page Dukane Corporation Audio Visual Products