Canon LV-S1 owner manual Appendix Lamp Replacement, Lamp Replace Counter

Page 38

APPENDIX

LAMP REPLACEMENT

When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

 

 

CAUTION

 

 

 

 

For continued safety, replace with a lamp

 

 

 

Do not drop a lamp assembly or touch a glass

 

 

 

 

assembly of the same type.

 

 

 

bulb! The glass can shatter and may cause

 

 

 

 

Allow a projector to cool for at least 45

 

 

 

injury.

 

 

 

 

minutes before you open Lamp Cover. The

 

 

 

 

 

 

 

 

 

 

 

 

 

inside of a projector can become very hot.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Follow these steps to replace the lamp assembly.

1

Turn off the projector and disconnect AC plug. Allow the

 

projector to cool for at least 45 minutes.

2

Remove a screw with a screwdriver to remove Lamp Cover.

3

Remove 2 screws with a screwdriver and pull out Lamp

 

Assembly by grasping Handle.

4

Replace Lamp Assembly with a new one and tighten 2 screws

 

back. Make sure that Lamp Assembly is set properly. Replace

 

Lamp Cover and tighten a screw.

5

Connect AC Power Cord to the projector and turn it on.

6

Reset Lamp Replace Counter (refer to the section “Lamp

 

Replace Counter” below).

NOTE : Do not reset Lamp Replace Counter when Projection Lamp is not replaced.

LAMP COVER

HANDLE

LAMP

ASSEMBLY

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give the following information to the dealer.

Model No. of your projector : LV-S1

Replacement Lamp Type No. : LV-LP12

(Service Parts No. 610 293 8210)

LAMP REPLACE COUNTER

Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting.

1

Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to

 

move a red frame pointer to SETTING Menu icon (refer to page 35, 36).

2

Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SET button. The

 

message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SET button.

3

Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.

Do not reset Lamp Replace Counter except after Projection Lamp is replaced.

38

Image 38
Contents LV-S1 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design One-Touch Auto PC AdjustmentHOT AIR Exhausted PreparationName of Each Part of Projector For Continental Europe SETTING-UP ProjectorConnecting AC Power Cord Room Light Adjustable FeetPreparation Positioning Projector Preparation Mounting Lens Cover Moving ProjectorVideo Connecting ProjectorTerminals of Projector AV AudioConnecting to Computer Terminals ProjectorConnecting to Video Equipment Audio OUTOperation of Remote Control Before OperationBefore Operation Operating Range Remote Control Battery InstallationBattery TOP Controls and Indicators SET ButtonFlow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Before Operation Menu BAR Guide WindowTurning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentBasic Operation No Show Function Sound AdjustmentTimer Function Direct OperationSelecting Computer System Computer InputSelecting Input Source Select Computer System ManuallyFreq Computer Input Compatible Computer SpecificationsResolution KHzPC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Image Level Select Menu Picture Image AdjustmentImage Level Select Direct Image Select MenuComputer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input AV System Menu Video or S-VIDEO Selecting Video SystemAuto AV System Menu Component VideoCinema Video Input Image Level Adjustment To Store icon and press SET button. The message OK? will Setting Menu SettingSetting Menu Remote control To change the code of the Remote Control UnitPower management Lamp counter resetCleaning Projection Lens MaintenanceAIR Filter Care and Cleaning AppendixAppendix Lamp Replacement Lamp Replace CounterTroubleshooting Remote Control Unit Does not workOptional Parts USB Connector Series B Appendix Configurations of the TerminalsControl Port Connector Computer Input Terminal AnalogPage Canon CANADA, INC