Guiding Signals
|
| Control | Indicator | ||
|
| Buttons | |||
Projector Status | Description |
|
| ||
|
|
| |||
Power | TEMP | LAMP | |||
|
| ||||
|
| (Amber) | (Amber) | ||
|
|
| |||
|
|
|
|
| |
Standby mode | Projector in Standby mode. Ready to power on. | BLUE | OFF | OFF | |
|
| Flashing | |||
|
|
|
| ||
|
|
|
|
| |
Warming up mode | Projector takes some time to warm up and power | BLUE | OFF | OFF | |
| on. | ||||
|
|
|
| ||
|
|
|
|
| |
Lamp on | Projector in Normal mode, ready to display an |
|
|
| |
| image. | BLUE | OFF | OFF | |
| Note: The OSD menu is not accessed. |
|
|
| |
|
|
|
|
| |
Cooling mode | Projector is cooling to shutdown. | BLUE | OFF | OFF | |
|
|
|
|
| |
Power Saving mode | Power Saving mode has been activated. The | AMBER |
|
| |
| projector will automatically enter standby mode, if | OFF | OFF | ||
| Flashing | ||||
| an input signal is not detected in two hours. |
|
| ||
|
|
|
| ||
|
|
|
|
| |
Cooling before | The projector takes 60 seconds to cool down before | AMBER | OFF | OFF | |
Power Saving mode | entering Power Saving mode. | ||||
|
|
| |||
|
|
|
|
| |
Projector | Air vents might be blocked or ambient temperature |
|
|
| |
overheated | may be above 35ºC. The projector automatically |
|
|
| |
| shuts down. Ensure that the air vents are not | OFF | AMBER | OFF | |
| blocked and that the ambient temperature is | ||||
|
|
|
| ||
| within operational range. If the problem persists, |
|
|
| |
| contact Dell. |
|
|
| |
|
|
|
|
| |
Lamp driver | The lamp driver is overheated. The air vents may |
|
|
| |
overheated | be blocked. The projector automatically shuts | AMBER | AMBER | OFF | |
| down. Turn the display on again after the projector | ||||
|
|
|
| ||
| cools down. If the problem persists, contact Dell. |
|
|
| |
|
|
|
|
| |
Fan breakdown | One of the fans has failed. The projector |
| AMBER |
| |
| automatically shuts down. If the problem persists, | ÒFF | OFF | ||
| Flashing | ||||
| contact Dell. |
|
| ||
|
|
|
| ||
|
|
|
|
| |
Lamp driver | The lamp driver has failed. The projector |
|
|
| |
breakdown | automatically shuts down. Unplug the power cord | AMBER | OFF | AMBER | |
| after three minutes then turn the display on again. | Flashing | Flashing | ||
|
| ||||
| If this problem persists, contact Dell. |
|
|
| |
|
|
|
|
| |
Color Wheel | Color wheel cannot start. The projector has failed |
|
|
| |
breakdown | and the projector automatically shuts down. |
| AMBER | AMBER | |
| Unplug the power cord after three minutes and | BLUE | |||
| Flashing | Flashing | |||
| then turn on the projector. If this problem persists, |
| |||
|
|
|
| ||
| contact Dell. |
|
|
| |
|
|
|
|
| |
Fault - DC supply | Power supply has been interrupted. The projector |
|
|
| |
(+12V) | automatically shuts down. Unplug the power cord | AMBER | AMBER | AMBER | |
| after three minutes and then turn on the projector. | Flashing | |||
|
|
| |||
| If this problem persists, contact Dell. |
|
|
| |
|
|
|
|
| |
Lamp module | Lamp module connection may be disrupted. Check |
|
| AMBER | |
connection failed | the lamp module and ensure that it is properly | OFF | OFF | ||
Flashing | |||||
| installed. If the problem persists, contact Dell. |
|
| ||
|
|
|
| ||
|
|
|
|
| |
Troubleshooting Your Projector
67