Dymo Comprehensive Guide for the DYMO 1000 Label Maker and Its Functions

Symbols and special characters

International characters

You can create international characters by combining a letter and a diacritical (accent). Diacriticals available on the keyboard are ´ ` ¨and ^. To add a diacritical to a character, enter the character first, followed immediately by the diacritical. For

Troubleshooting

No display

• check machine is on
•	replace discharged batteries
	or use the AC adaptor
•	check AC adaptor plugged
	in and switched on.

DYMO 1000

Electronic Labelmaker

Instructions for Use

example, press ‘E’ followed by ‘´’ to get é .		to
To add a diacritical to an existing character, use < or	<

place the cursor under the character to be changed, then press the appropriate diacritical key.

Symbols

Pressing SYM changes the display to show symbols and special characters, some of which are not available direct from the keyboard. The display will show:

a-o?(or a-r ? where available).

Each letter selects a line of five symbol characters, as shown in the table below. Note that some of the more complex printed symbols are represented by simpler symbols in the display.

Press	DEL	to cancel or press the letter key required.
Use <	or	<	to select a symbol. Press SYM again to place the
				1
				,
symbol in the label, or press				2
				,
				PRINT .	to place it and print the label.
				3
				.
				n.

No printing or poor text

•replace discharged batteries or use the AC adaptor

•check tape cassette installed correctly and tape not kinked

•replace the tape cassette.

No response to print key

• label length too short for text
– press	<	until >
disappears or clear fixed
length
• !!!!! in display indicates a
printer jam. Printing will stop
and the display return to
normal. Open the cassette
compartment and free the

Power supply

Insert five size AA alkaline or nickel-cadmium re-chargeable batteries, observing the polarity markings.

Re-chargeable batteries must be charged externally before use.

Cassette door

To remove the door, press in where shown below then swing the door open and lift it away.

When re-fitting, hold the door at the angle shown below and engage the tabs on the door in the slots in the case.

Now close the door, ensuring that the lever engages with the ramp on the door as it closes.

Cleaning

		Use a ball pen or
		pencil to hold down
Press	➊interlock button.
➋	➬
➭	➧	Use a cotton
	➧	➌ bud and alcohol
		to clean both
		sides of cutter
		blade regularly.

➍

➍ Check and clean

print head and

DISPLAYED CHARACTERS

a	$ ¢	£	Fr	¥
b	@ &	#	:	;

c" < > ± =

d\ ÷ X % *

e	°R °C MT			°
f	2 3 2	3	1/2
		μ		Ω

PRINTED CHARACTERS

$ ¢ £ Fr ¥ @ & # : ; " < > ± =

\÷ X % * ® © ™ ☎ °

2 3 2 3 1/2

μ Ω

	jam.
•			flashing in the display
		indicates low battery volts.
	Replace discharged
	batteries or use the AC
	adaptor.

Accessories

12mm (1/2") cassettes	45010
Black/Clear
Blue/Clear	45011

Cover slides

Connect the AC off. adaptor plug here. Use

only the recommended adaptor. Plugging in the AC adaptor disconnects the batteries.

Note: Re-chargeable batteries will not be charged.

Ensure this lever engages with ramp on door when closing.

pinch roller

regularly using

cotton bud and

alcohol ONLY.

Press here to open

Note: Rows p, q and r where available.

g
	.. . .. . .. . .. . .. .
h
	1 2	3 4	5
i	.. .	➞	➞
	6
j	Æ Å Ç Œ Ø

kæ å ç œ ø l Ã Ë Ñ Õ

m	ã	ë	ñ	õ
n	â	ê	î	ô	û

oß ¿ ¡ ● ★

pÁ É Í Ó Ú

q	á	é	í	ó ú
r	ì	ò	!

!

➞ ➞ ➞ ➞

ÆÅ Ç Œ Ø æ å ç œ ø

Ã Ë Ñ Õ

ãë ñ õ

â ê î ô û

ß¿ ¡ ● ★

Á É Í Ó Ú

á	é	í	ó ú
ì	ò	!

Red/Clear	45012
Black/White	45013
Blue/White	45014
Red/White	45015
Black/Blue	45016
Black/Red	45017
Black/Yellow	45018
Black/Green	45019
Replacement Cutter	15030
Carrying Case	15010
AC Adaptor	40030

This product is designed to conform with the following international standards:

EN 60950	Specification for safety
IEC 950	of information technology
UL 1950	equipment including electrical
	business equipment
EN 55022	Specification for limits and
Class B	methods of measurement of
	radio interference

Changing the cassette

Ensure tape and ribbon is taught across mouth of cassette and tape passes between the guide posts before installing.

Lift cassette straight up and out.

Make sure that this switch is set to the RIGHT before installing the cassette. A

Push firmly until cassette clicks into place.

	Print head
Label
cutter –	TAPE
press to	CASSETTE
cut off
printed
label.

Print contrast — may be adjusted by pressing	SYM	followed by the
space key to display five contrast symbols. Use	< or	<	to select a

symbol. Press SYM again to confirm the setting. The contrast level will revert to the mid-setting when the Labelmaker is turned off and on again.

	characteristics of information
	technology equipment.
FCC pt15	Federal communications
Sub pt B	commission radio frequency
Class B	emissions.
Written by	DAW Publications, Cambridge

notch in the cassette will fit over the switch when it is set correctly.

Ensure tape and ribbon are positioned as shown between print head and pinch roller.

6DYMO 1000

DYMO 1000 3