Delta Electronics DVPPF02-H2 specifications Connecting to Profibus DP Connector, Extension Port

Page 1

￿Specifications

PROFIBUS DP Connector

 

Interface

DB9 connector

 

Transmission

High-speed RS-485

 

method

 

Transmission cable

Shielded twisted pair cable

 

Electrical isolation

500V DC

Communication

Message type

Loop-type data exchange

Equipment ID

0AFE (hex)

 

Serial transmission

9.6kbps; 19.2kbps; 93.75kbps; 187.5kbps; 500kbps; 1.5Mbps; 3Mbps; 6Mbps;

 

speed supported

 

12Mbps (bits per second)

 

(auto-detection)

 

 

Environment

 

Standards

IEC 61131-2,UL508

Storage/operation

Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)

Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree 2

 

Shock/vibration

International standards: IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 & IEC

immunity

68-2-27 (TEST Ea)

Interference

RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1000MHz, 1.4GHz ~ 2GHz, 10V/m

EFT (IEC 61131-2, IEC 61000-4-4): Analog & Communication I/O: 1KV

immunity

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

 

Certificates

CE, UL

￿Connecting to PROFIBUS DP Connector

Insert the PROFIBUS DP bus connector into

the PROFIBUS DP connector on

DVPPF02-H2. Screw it tight to ensure

DVPPF02-H2 and the PROFIBUS DP bus

are properly connected.

￿Installation & Wiring

1.

Install DVPPF02-H2 in an enclosure with sufficient

D

D

 

space around it to allow heat dissipation (see the

 

 

 

figure).

EH2 PLC

PF0 2- H2

2.

D

 

D

DO NOT place the I/O signal wires and power

 

 

 

supply wire in the same wiring circuit.

D

D

D>5 0mm

￿Control Register

The control registers (CR) are the registers inside DVPPF02-H2. See the table below for the definitions of all the CRs. DVP-EH2 series PLC MPU can read or write the CR allowed through DFROM/DTO instructions.

 

 

 

注意事項

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

￿

 

 

 

 

 

 

 

 

 

 

 

 

￿

配線時

 

關閉電源。

 

 

 

 

 

 

 

本使用說明書僅提供電氣規格、功能規格、安裝配線、故障排除及周邊裝置部分說明，本使用說明書僅DVPPF02-H2PROFIBUS DP

 

 

 

 

PROFIBUS DP

 

 

 

 

協定的詳細內容這裏不作介紹。如果讀者想瞭

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

殼機配為線開箱放內型。機另殼必，須因具此備保護者措使施用（本如機：時特，殊必的須工將具其或安鑰裝匙於才具可防打塵開、），防防潮止及非免維於護電人擊員∕操衝作擊或意意外外的衝外

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

產品用來控制運轉中的機械及設備。為避免損壞本產品，只有合格且熟悉本產品結構及操作的專業人

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

交流輸入電源不可連接於輸入∕輸出信號端

否則可能造成嚴重損壞。請在上電前再次確認電源配線，

￿

 

 

 

 

 

 

 

 

務必正確的接地，以提高產品抗雜訊能力。

 

 

產品簡DVPPF02介 -H2

 

DVPPF02-H2

PROFIBUS DP

 

PROFIBUS DP

 

DVP-EH2

PLC

 

 

DVPPF02-H2

通訊模組，可用於DVP-EH2

 

 

 

DVP-EH2

 

 

 

 

 

 

主機連

￿

使用前

 

仔細閱讀本

手冊 並依照本手冊指示進行操作，以免造成產品受損或人員受傷。

1.

 

 

 

DP

 

 

 

 

 

 

 

 

2.

 

 

 

請務必

 

 

GSD

 

 

 

 

 

PROFIBUS DP

 

 

 

 

 

 

作為

 

 

 

操作指南和入門參考，

 

 

 

 

 

 

解更多

 

 

協定使用的內容，請參閱相關專業文章或書籍資料。

 

 

擊本體，造成危險及損壞。

 

 

 

 

 

 

 

員才可進行本產品的安裝、操作、配線及維護。

 

 

 

 

且請勿在上電時觸摸任何端子。本體上的接地端子

 

 

 

￿Components

￿PROFIBUS DP Connector

To connect to PROFIBUS DP network, use standard DP connector for the wiring.

CR#

#0

#1

#2

Attribute

Read

Read

Read

Content

Model name

Firmware version

Length of I/O data

High byte

Low byte

 

 

DVPPF02-H2 model code = H’0250

Displaying the current firmware version in hex, e.g. V1.00 is indicated as H’0100.

Length of output I/O data Length of input I/O data

3.

PROFIBUS DP

 

4 (slot)

 

 

 

 

4.

 

 

 

 

 

12Mbps

 

 

 

 

5.

I/O

 

 

 

PROFIBUS DP

 

,

 

100

word

 

4

slot

 

 

 

 

100

word 4 slot

 

，

6.

 

 

 

 

網路通訊模組。

定義為

配置長度之和）。

謝謝您使用台達

 

無需外接電源，與

 

 

接好後由

 

網路與

系列

主機的連接，

 

 

 

 

 

主機提供電源。

 

 

 

 

 

PIN

1

2

3

4

5

6

7

8

9

PIN name

-

-

Rxd/Txd-P

-

DGND

VP

-

Rxd/Txd-N

-

Definition

Not defined

Not defined

Sending/receiving data P(B)

Not defined

Data reference potential

Power voltage - positive

Not defined

Sending/receiving data N(A)

Not defined

9 5

6 1

#3 ~ #102

#103 ~ #202

#203 ~ #206

#207 ~ #250

#251

#252 ~ #383

#384 ~ #511

Write/read

Read

Read

Input data mapping

Output data mapping

Error

Area for storing data from DVPPF02-H2 to PROFIBUS DP master

Area for storing data from PROFIBUS DP master to DVPPF02-H2.

Set up by the system. DO NOT use it.

Reserved

Register for storing errors. See ￿ for error codes.

Reserved

Set up by the system. DO NOT use it.

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

1

 

 

 

 

 

 

 

1 6

 

 

 

 

 

 

 

 

 

 

 

 

2

 

 

1 6

 

4

 

 

 

 

 

 

2

 

 

 

 

 

 

 

色40 [1.575]

 

 

 

 

 

 

 

3

POWER LED

 

 

6

 

 

1

 

 

 

 

 

 

4

NET LED

 

 

 

 

]

 

 

 

 

 

 

 

 

 

 

 

[3 5.43

 

 

 

 

 

8

 

 

 

 

 

 

 

 

 

 

 

 

5

PROFIBUS DP

 

 

 

90

 

 

 

 

 

 

 

 

6

 

 

 

 

5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

DIN

 

 

 

 

6]

 

 

 

82 [3.228]

 

7

 

8

DIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

27

 

 

 

 

 

 

 

 

 

 

 

 

 

功能特.

 

 

 

 

 

 

 

 

 

 

 

 

 

0

主站與多個從站之間的迴圈資料傳輸。

 

 

 

 

 

 

 

 

 

[

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

支持

 

 

 

 

 

 

 

 

在

 

 

 

網路配置工具中

mm

槽

文檔。

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

。

配置。

 

 

 

 

 

 

 

自動偵測通訊速率，最高通訊速率支援

 

 

輸入資料長度總和最大可配置

個

 

 

資料長度可通過

 

網路配置工具自由

 

（ 個

 

配置長度之和），輸出資料長度總和最大可配置

 

個

 

（ 個

 

 

 

錯誤碼診斷功能。

 

 

 

 

 

 

 

 

 

 

 

 

產品外觀及各部介紹

 

 

 

 

 

 

 

位址設定開關埠

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

指示燈

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

指示燈

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

擴充模組連接

 

Warning

￿ Please read this instruction sheet carefully before use and follow this instruction to operate the device in order

to prevent damages on the device or injuries to staff.

￿ Switch off the power before wiring.

￿ This instruction sheet only provides introductory information on electrical specification, functions, wiring,

trouble-shooing the peripherals for DVPPF02-H2. Details of PROFIBUS DP protocol are not included in this

sheet. For more information on PROFIBUS DP protocol, please refer to relevant reference or literatures.

￿ DVPPF02-H2 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust,

humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the

device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device

may occur.

￿ DVPPF02-H2 is to be used for controlling the operating machine and equipment. In order not to damage it,

only qualified professional staff familiar with the structure and operation of if can install, operate, wire and

maintain it.

￿Address Setup Rotary Switch

The two rotary address setup switches set up the node addresses on

 

 

PROFIBUS DP network in hexadecimal form. Setup range: 0x01 ~ 0x7D (0 or

1

RESS

0x7E ~ 0xFF are forbidden).

 

 

 

x1 6

 

 

 

 

DE ADD

 

 

 

 

 

 

0

Rotary switch

 

 

x 161

 

x 160

x1 6

NO

Multiple

 

 

× 16

 

× 1

 

 

Example: If you need to set the node address of DVPPF02-H2 as 26 (1A Hex), simply switch the corresponding rotary switch of x161 to “1" and the corresponding rotary switch of x160 to”A”.

 

 

Switch setting

 

 

 

 

 

Description

￿Note: The changed values on switches are

 

 

0x01 ~ 0x7D

 

Valid PROFIBUS DP address

only valid when DVPPF02-H2 is re-powered.

 

 

 

When DVPPF02-H2 is operating, changing

 

0 or 0x7E ~ 0xFF

 

Invalid PROFIBUS DP address

the set value of the address will be regarded

 

 

invalid.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿LED Indicators & Trouble-Shooting

There are 2 LED indicators on DVPPF02-H2. POWER indicator displays the status of the working power. NET indicator displays the connection status of the communication.

￿POWER LED

LED status

 

Indication

 

 

How to deal with it?

Green light on

 

The power is normal.

 

--

 

 

 

 

 

 

 

 

 

 

 

1.

Check if the power of DVP-EH2 is normal.

Off

 

No power

 

2.

Check if the connection between DVPPF02-H2

 

 

 

 

 

and DVP-EH2 is normal.

￿NET LED

￿

 

 

 

 

 

 

通訊連接器

PROFIBUS DP

 

 

 

 

 

 

 

 

DB9

 

 

 

 

 

 

 

RS-485

 

 

 

 

 

500V DC

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

ID

 

0AFE (hex)

 

 

頭

 

 

 

 

 

 

 

 

 

9.6kbps; 19.2kbps; 93.75kbps; 187.5kbps; 500kbps; 1.5Mbps; 3Mbps; 6Mbps;

 

 

支持

 

 

固定扣

 

功能規格

12Mbps

 

軌槽

 

 

尺寸單位：

 

 

 

 

連接器

 

 

 

 

 

￿ DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur.

Check all the wiring again before switching on the power, and DO NOT touch any terminal when the power is

switched on. Make sure the ground terminal

is correctly grounded in order to prevent electromagnetic

interference.

 

￿ Introduction

 

Thank you for choosing Delta DVPPF02-H2 PROFIBUS DP communication module. DVPPF02-H2 can be applied to the connection with DVP-EH2 series PLC MPU in a PROFIBUS DP network. DVPPF02-H2 does not need to be connected to an external power supply. The power will be supplied from DVP-EH2 once it is connected to DVP-EH2.

￿Extension Port

The extension port on DVPPF02-H2 is used for the connection to the next DVPPF02-H2 or extension modules of DVP-EH2 series PLC MPU.

￿Basic Operation

￿Connecting DVPPF02-H2 to DVP-EH2 Series PLC MPU

LED status

Off

Red light on

Red light flashes

Indication

No power

DVPPF02 is operating but is not connected to PROFIBUS DP bus.

Depending on the value in CR#251

How to deal with it?

1.Check if the power of DVP-EH2 is normal

2.Check if the connection between DVPPF02-H2 and DVP-EH2 is normal

Check if DVPPF02-H2 is normally connected to PROFIBUS DP bus.

See the error code table for how to deal with it.

接頭

 

IEC 61131-2,UL508

 

 

 

 

-25°C ~ 70°C

5 ~ 95%

 

 

 

0°C ~ 55°C

50 ~ 95%

2

 

 

 

IEC 61131-2, IEC 68-2-6 (TEST Fc)/IEC 61131-2 & IEC 68-2-27

 

(TEST Ea)

 

 

 

 

RS (IEC 61131-2, IEC 61000-4-3): 80MHz ~ 1000MHz, 1.4GHz ~ 2GHz, 10V/m

 

EFT (IEC 61131-2, IEC 61000-4-4): Analog & Communication I/O: 1KV

 

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

 

方式

高速

接頭

 

 

 

 

雙絞線

 

 

 

傳輸電纜

遮罩

 

 

 

電氣隔離

迴圈式資料交換

 

 

通訊

 

 

 

資訊類型

 

 

設備

 

 

 

 

 

支援串列傳輸速度

 

 

 

 

 

￿ Features

1. Supports loop-type data exchange between DP master and many slaves.

Switch off DVP-EH2. Open the connection

port on the right hand side of DVP-EH2 and

connect DVPPF02-H2 to DVP-EH2. Switch

Green light on

DVPPF02-H2 is in data exchange status.

--

（自

偵測）

CE

UL

 

（位元∕秒）

環境規格

 

 

2.

Supports GSD files in PROFIBUS DP network configuration tools.

3.

Supports 4 slots in PROFIBUS DP network configuration tools.

4.

Auto-detects baud rates; supports Max. 12Mbps.

5.

The length of I/O data can be freely configured through PROFIBUS DP network configuration tools.

 

Max. input data length = 100 words (the sum of 4 slots); Max. output data length = 100 words (the

 

sum of 4 slots).

D V P - 2 0E H

on DVP-EH2, and DVP-EH2 will supply

power to DVPPF02-H2. There is no need to

connect DVPPF02-H2 to an external power

supply.

￿Error Codes

CodeDescription

00

DVPPF02-H2 operates normally.

 

 

 

 

 

 

 

 

 

 

 

 

How to deal with it?

--

￿

 

 

 

￿ PROFIBUS DP

 

 

 

PROFIBUS DP

 

PROFIBUS DP

 

標準

儲存

標準

（濕度）

操作∕儲存環境

（溫度），

耐震動∕衝擊

操作：

（溫度），

（濕度），污染等級

國際標準規範

 

 

6. Error code diagnosis.

￿ Product Profile & Outline

￿Installing DVP-EH2 and DVPPF02-H2 on DIN Rail

01

Hardware error

02

PROFIBUS DP watch dog error

Send your DVPPF02-H2 back to the factory for repair.

Check if DVPPF02-H2 is normally connected to PROFIBUS DP bus.

 

/

1

-

2

-

雜訊免疫力

 

 

1 6

3

2

 

4

 

1 6

 

6

]

1

 

9 0[3 5. 43

 

 

5

 

 

]

 

276

40 [1.575]

.

0[

 

7

 

Unit: mm

82 [3.228]

1 Extension port

2Address setup switch

3POWER indicator

84 NET indicator

5 PROFIBUS DP connector

6 Extension module interface

7 DIN rail clip

7

8 DIN rail

 

1.

Use 35mm DIN rail.

2.

Open the DIN rail clips on DVP-EH2 and

 

DVPPF02-H2. Insert DVP-EH2 and

DV P-20E H

DVPPF02-H2 on the DIN rail.

 

3.

Clip up the DIN rail clips on DVP-EH2

 

and DVPPF02-H2 to fix DVP-EH2 and

 

DVPPF02-H2 on the DIN rail.

03

Address setup error (0, or exceeding

0x01 ~ 0x7D)

 

0424V low voltage error

055V low voltage error

Set the address within the range 0x01 ~ 0x7D and re-power DVP-EH2.

Check if the power voltage of DVP-EH2 is normal; check if DVPPF02-H2 is normally connected to DVP-EH2.

Send your DVPPF02-H2 back to the factory for repair.

3

 

Rxd/Txd-P

 

 

P (B)

9

5

 

 

 

 

 

 

4

 

-

 

 

 

 

 

5

 

DGND

 

 

 

 

 

6

 

VP

 

 

-

6

1

 

 

 

 

 

7

 

-

 

 

 

 

 

8

 

Rxd/Txd-N

 

N (A)

 

 

9

 

-

認證、

認證

 

 

 

認證專案

 

 

 

 

 

各部分元件介紹

 

接收電資∕源定料發未電義參送指連壓考說資定接接明正料器地壓進行配線。

 

 

與接腳

網名路稱連接通時訊，使連用接標準器

 

 

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Installation & Wiring Connecting to Profibus DP ConnectorProfibus DP Connector Address Setup Rotary Switch双绞线 的方向插入数据交换 （湿度）

DVPPF02-H2 specifications

Delta Electronics has consistently been a front-runner in providing innovative and efficient power solutions. The Delta DVPPF02-H2 is a notable addition to their lineup, designed to meet the demands of various industrial applications. This power supply unit is renowned for its reliability, performance, and comprehensive feature set.

One of the main features of the DVPPF02-H2 is its high efficiency. With an efficiency rating often exceeding 90%, this power supply is capable of minimizing energy loss, which is a crucial factor for today's energy-conscious businesses. This efficiency not only reduces operational costs but also contributes to a lower carbon footprint, aligning with global sustainability goals.

The DVPPF02-H2 incorporates advanced technologies to enhance its performance. One of these technologies is the Active PFC (Power Factor Correction), which ensures that the power supply operates efficiently across a range of load conditions. This feature improves the system's power factor, allowing for reduced electricity consumption and compliance with international regulations.

In terms of output characteristics, the DVPPF02-H2 delivers stable and reliable power, making it ideal for various industrial applications, including automation, telecommunications, and medical devices. It offers multiple output voltages and current options, ensuring that it can accommodate diverse equipment requirements. The unit also features over-voltage protection, over-current protection, and short-circuit protection, providing added security and reliability for connected devices.

Durability is another hallmark of the DVPPF02-H2. Built with rugged materials and designed to operate in challenging environments, this power supply is capable of withstanding temperature variations and electrical disturbances.

Additionally, the compact design of the DVPPF02-H2 facilitates easy integration into existing systems, without requiring excessive space. Its cooling system, often equipped with fans or heatsinks, allows for efficient thermal management, ensuring optimal performance over extended periods of operation.

In summary, the Delta DVPPF02-H2 is a robust and efficient power supply that stands out with its high efficiency, advanced technologies, and reliable output characteristics. Its design caters to the needs of a wide range of industrial applications, making it a trusted choice for businesses looking to enhance their operational efficiency while mitigating environmental impact. Whether for automation, telecommunications, or medical equipment, the DVPPF02-H2 showcases Delta Electronics’ commitment to quality and innovation in power supply solutions.
Top Page Image Contents