Delta Electronics DVP-EC3 specifications 消耗 力

Warning

￿This instruction sheet provides only information on the electrical specification, general functions, installation and wiring. The program design and applicable instructions for DVP-EC3 are the same as those applicable for DVP-ES series. For detailed information, please refer to “DVP-PLC Application Manual: Programming”. For details of the optional peripheral, please refer to the instruction sheet enclosed in it.

￿DVP-EC3 series PLC is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required for operating the enclosure) in case danger and damage on the device may occur.

￿DO NOT connect the input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check

all the wiring again before switching on the power. Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference.

￿Introduction

Thank you for choosing Delta DVP-EC3 series programmable logic controller. DVP-EC3 currently offers 10-16 I/O points. To ensure proper installation, operation and maintenance, please read this instruction sheet carefully and provide users with this instruction sheet before installing DVP-EC3.

￿ Product Profile & Outline

￿Specifications

Model	DVP10EC00	3	DVP14EC00	3	DVP16EC00	3
Item
Power supply voltage	100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%
	DVP-EC3 starts to run when the power supply rises to 95 ~ 100V AC and stops
Operation	when the power supply drops to 70V AC. It continues to run for 10ms after the
	power supply is cut off.
Power supply fuse	2A/250V AC
Power consumption	9VA
DC24V Supply Current	100mA
Power supply protection	DC24V output short circuit protection
Voltage withstand	1,500V AC (Primary-secondary), 1,500V AC (Primary-PE), 500V AC
	(Secondary-PE)
Insulation resistance	> 5M￿ at 500V DC (between all I/O points and earth)
	ESD: 8KV Air Discharge
Noise immunity	EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
	RS: 26MHz ~ 1GHz, 10V/m
	The diameter of grounding wire shall not be less than that of L, N terminal of the
Earth	power supply. (When many PLCs are in use at the same time, please make sure
	every PLC is properly grounded.)
Operation/storage	Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), Pollution degree2
	Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)
Vibration/shock	International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/ IEC61131-2 & IEC
resistance	68-2-27 (TEST Ea)
RS-485 communication	Not supported□		Not supported□		Supported	□
mode
Weight (g)	R: 192g; T: 180g		R: 202g; T: 185g		R: 212g; T: 190g

Input Point

Input point type	Digital Input
Input type	DC (SINK or SOURCE)
Input current	24V DC 5mA

Off → On, > 15V DC

Action level

	On → Off, < 5V DC
Reaction time
(Conversion sampling	Approx. 10ms (0 ~ 20ms adjustable in D1020)
time)

Output Point

Output point type	Relay-R		Transistor-T
Current specification	2A/1 point (5A/COM)		0.5A/1 point (2A/COM)
			5 ~ 30V DC
Voltage specification	< 250V AC, 30V DC	(UP, ZP must work wit external
		auxiliary power supply 24V DC -15%
		~ +20%, rated consumption approx.
			1mA/point)
Maximum load	75VA (inductive)		15W/1 point (Resistive)
	90W (resistive)
Reaction time	Approx .10ms	Off	On 30us, On	Off 100us

￿ Installation & Wiring

3.1

I/O Terminal Layout

DVP10EC00R3/T3

+24V 24G S/S

X0

X1

X2

X3

X4

X5

+24V 24G

S/S

X0

X1

X2

X3

X4

X5

D VP 10 EC 00 R3 (6 DI -DC / 4D O- R)

DVP10EC00 T3 (6DI- DC / 4DO- T)

C0

Y0

Y1

Y2

Y3

UP

ZP

Y0

Y1

Y2

Y3

DVP14EC00R3/T3

→

→

+24V 24 G S/ S

X0

X1

X2

X3

X4

X5

X6

X7

DVP14 EC00R3 (8DI- DC / 6 DO-R)

C0

Y0

Y1

Y2

Y3

C1

Y4

Y5

+24V 24G S/S

X0

X1

X2

X3

X4

X5

X6

X7

D VP14 EC 00 T3 (8 DI- DC / 6 DO -T)

◎

UP

ZP

Y0

Y1

Y2

Y3

Y4

Y5

DVP16EC00R3/T3

+24V 24G S/S

X0

X1

X2

X3

X4

X5

X6

X7

D+

D-

SG

DVP16EC00R3 (8DI -DC / 8DO-R)

C0

Y0

Y1

Y2

Y3

C1

Y4

Y5

Y6

Y7

+24V 24G S/S

X0

X1

X2

X3

X4

X5

X6

X7

D+

D-

SG

1.The input voltage should be 100 ~ 240VAC. The power supply should be connected to L and N terminals. Please note that wiring AC110V or AC220V to +24V output terminal or digital input points will result in serious damage on it.

2.Use 1.6mm wire (or longer) for the grounding of it.

3.The power shutdown of less than 10ms will not affect the operation of it. However, power shutdown time that is too long or the drop of power supply voltage will stop the running of it, and all outputs will go “OFF”. When the power supply turns normal again, DVP-EC3 will automatically return to its operation. (Please be aware of the latched auxiliary relays and registers inside DVP-EC3 when programming.)

4.For max. output of the +24V power supply output terminal for each model, please refer to the electrical specification table. DO NOT connect other external power supplies to this terminal. Every input point requires 5 ~ 7mA to drive (e.g. 16 input points will require 80 ~ 112mA to drive). The +24V input on DVP- EC3 is only for digital input points; other external loads are not suggested.

	+2 4V	24 G	S/S	X0	X1	X2
5V	DC/ DC
						2. 0A
	L	N
10 0~240 VAC

￿Safety Wiring

Since DVP-EC3 controls many devices, actions of any device may affect actions of other devices, and the breakdown of any one device may cause the breakdown of the entire auto-control system and danger. Therefore, we suggest you wire a protection circuit at the power supply input terminal, as shown in the figure below.

1	AC power supply load
2	Power supply circuit protection fuse (3A)
3	POWER indicator
4	Emergency stop: This button can cut off the system
	power supply when accidental emergency takes place
5	Breaker

6 DVP-EC3 (main processing unit)

7 Earth resistance: < 100￿

8 Power supply: 100 ~ 240V AC, 50/60Hz

○

￿I/O Point Wiring

The input signal of the input point is the DC power DC input. There are two types of DC type wiring: SINK and SOURCE, defined as follows:

◎	Input Point Loop Equivalent Circuit & Wiring
		+2 4 V	+5 V
		24 V D C
		24 G
	DC Signal IN	S/ S
	(SINK mode)	X0
		X1
		+24V
		24VDC	+5V
		24G
	DC Signal IN
	(SOURCE mode)	S/S
		X0
		X1

Below is an example. For detailed point configuration, please refer to specifications of each model:

￿

注意事項

DVP本使用說明書提供給使用者電氣規格、功能規格、安裝配線之相關注意事項。其他詳細之程式設計及指令與-ESDVP-PLC

應用技術手冊【程式篇】，選購之周邊裝置詳細說明請見該產品

￿

(OPEN TYPE)

擊意外之外殼配線箱內。另必須機具殼備，保因護此措使施用（者如使：用特本殊機之時工，具必或須鑰將匙之才安可裝打於開具）防防塵止、非防維潮護及人免員於操電作擊或∕意衝

￿

交流輸入電源不可連接於輸入∕出信號端，否則可能造成嚴重損壞，請在上電之前再次確認電源配線。請勿

￿

產品簡DVP介-EC3

DVP-EC3

10 ~ 16

點數的主機。為了確保能夠正確

￿

C O M 2

(R S - 48 5 )

+ 24V 24G S/ S X0 X1

X2 X3

X4 X5

X6 X7

D+ D- SG

C O M2

PO WE R

RUN

ERRO R

D V P 1 6E C

8DI-DC /8DO-R

C O M1

電源、運行及錯誤指輸示入燈C O M/1輸出點指示燈

系列相直流電源直接輸固出輸定入孔點指標容，詳細說明請見

隨

。

( RS - 2 32 C )

L

N

C0 Y0 Y1 Y2 Y3 C1 Y4 Y5

Y6 Y7

使用說明書 機種型號

機為開放型

外衝擊本體，造成危險及損壞。

D IN

( 3 5 mm )

務必正確的接地，可提高產品抗雜訊能力。

D IN

￿

在上電時觸摸任何端子 本體上之接地 子

感謝您採用台達

系列可程式控制器。

系列目前提供

及交由該機器的使用者。

地安裝及操作可程式邏輯控制器，請在裝機之+ 24V 24G S/S X0 X1前X2 ，詳細閱讀本使用手冊，並請妥善保存X3 X4 X5 X6 X7 D+ D- SG

產品外觀及各部介紹

C O M2

通訊口

IN

0

1

2 3

4

5

6

7

PO WE R

R U N

OUT

E R RO R

0 1 2 3 4 5 6 7

9 0 m m

9 9 m m

DVP16EC

8DI-DC / 8DO-R

C O M1

L

N

C0 Y0

Y1 Y2

Y3 C1

Y4

Y5 Y6

Y7

9 0 .5 m m

9 5 m m

4 8 .5 m m

交流電源輸入

程式通訊口

輸出點指標

軌槽

軌固定扣

￿

固定式輸出 / 入端子

直接固定孔

電氣規格

尺寸規格

DVP10EC00

3

DVP14EC00

3

DVP16EC00 3

機種

100 ~ 240V AC (-15% ~ 10%), 50/60Hz ± 5%

95 ~ 100V

AC

DVP-EC3

70V AC

DVP-EC3

當電源緩升至

10ms

□

2A/250V AC

9VA

DC24V

100mA

DC24V

1,500V AC (Primary-secondary)

1,500V AC (Primary-PE)

500V AC (Secondary-PE)

5M￿

/

500V DC

ESD: 8KV Air Discharge

EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V

項目

壓

□

時，

□

會停止動作。電源瞬間斷電

開始動作，當電源緩降至

時，

動作規格

以內繼續運行。

Inpu t po ints Ind i c atio n		P OW ER , R U N & ER RO R i n dic a tors
D ir ec t m oun ting ho l e		C OM 2 C om mun i ca ti on
		p ort (RS - 48 5 )
	+ 24 V24 G S/ S X 0 X 1 X 2 X3	X 4 X5 X 6 X 7 D + D - S G
D C p ow e r s u pp l y o u tpu t		CO M2
	PO WE R	I/O p oin t in di ca to rs
	R UN
	ER RO R
M od el n a me	DVP1 6EC	C OM 1 C om mu n i ca tion
	8DI-DC / 8DO-R	CO M1
A C p ow e r s u pp l y in put		por t (RS -23 2C)
	L NC 0 Y0 Y1 Y 2 Y 3 C 1 Y 4 Y 5 Y 6 Y 7
O utp ut poi nts In d ic a tio n
		D IN r ai l (35m m)
D IN rai l c li p		D ir ec t m ou ntin g ho l e

F ix ed I/O te r min als

￿Dimensions

DVP16EC00T3 (8DI -DC / 8DO- R)

UP ZP Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7

1.Use the 12-24 AWG single-core bare wire or the multi-core wire for the I/O wiring, and please use 60/75°C copper conductor only. The twisting power of the screw for the DVP-EC3 terminal is 3.80 kg-cm (3.30 lb-in) .

2.DO NOT wire empty terminal. DO NOT place the input signal wire and output power wire in the same wiring circuit.

3.DO NOT drop tiny metallic conductor into DVP-EC3 while screwing and wiring

3.2Mounting & Installation

Please install PLC in an enclosure with sufficient space around it to allow heat dissipation. For heat dissipation, make sure to provide a minimum clearance of 50mm between the unit and all sides of the cabinet. (See the figure.)

◎

Relay (R) Output Circuit Wiring

1Flywheel diode: To extend the life span of contact

2Emergency stop: Uses external switch

3Fuse: Uses 5 ~ 10A fuse at the shared terminal of output contacts to protect the output circuit

4Varistor: To reduce the interference on AC load

5Empty terminal: Not in use

6DC power supply

7Neon indicator

8AC power supply

9Incandescent light (resistive load)

Manually exclusive output: Uses external circuit and forms an interlock, together with DVP-EC3 internal

10program, to ensure safety protection in case of any unexpected errors.

RS: 26MHz ~ 1GHz, 10V/m

L, N

PLC

/

操作：

0°C ~ 55°C

50 ~ 95%

2

-25°C ~ 70°C

5 ~ 95%

/

IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

RS-485

,g

R 192g

T 180g

R

202g T 185g

R 212g T 190g

險絲容

消耗 力

SINK

SOURCE

供應電流

24VDC

5mA

電源保護

輸出具短路保護

突波電壓耐受量

Off → On

15V DC

On → Off

5V DC

絕緣阻抗

10ms

D1020

0 ~ 20ms

）

以上（所有輸出 入點對地之間

雜訊免疫力

接地配線之線徑不得小於電源端

之線徑（多台

同時使用時，請務必單點接地）

接地

操作 儲存環境

儲存

（溫度），

（濕度）污染等級

耐振動 衝擊

（溫度），

（濕度）

國際標準規範

不支援

支援

通訊模式

不支援

9 0 m m

+ 24V 24G S/S X0		X1	X2	X3 X4	X5	X6	X7	D+	D-		SG
									C O M2
						IN
						0 1	2 3	4	5	6	7
				PO WE R
				R U N		OUT
				E R RO R		0 1 2 3 4 5 6 7
											9 9 m m
DVP16EC
8DI-DC / 8DO-R						C O M1
L	N	C0	Y0	Y1 Y2	Y3	C1	Y4	Y5 Y6			Y7
	9 0 .5 m m
	9 5 m m

4 8 .5 m m

How to screw: Please use M4 screw according to the dimension of the product.

How to install DIN rail: PLC can be secured to a cabinet by using the 35mm DIN rail. When mounting PLC to DIN rail, be sure to use the end bracket to stop any side-to-side movement of it and reduce the change of wires being loosen. A small retaining clip is at the bottom of it. To secure PLC to DIN rail, place the clip onto the rail and gently push it up. To remove it, pull the retaining clip down and gently remove it from DIN rail.

3.3Wiring Notes

￿Specification & Wiring of Power Supply

The power supply input for DVP-EC3 model is AC input. When operating DVP-EC3, please make sure that:

◎

Transistor (T) Output Circuit Wiring

1DC power supply

2Emergency stop

3Circuit protection fuse

The output of the transistor model is “open

4collector”. If Y0/Y1 is set to pulse output, the output current has to be 0.05 ~ 0.5A to ensure normal operation of the model.

Manually exclusive output: Uses external circuit and

5forms an interlock, together with DVP-EC3 internal program, to ensure safety protection in case of any

○ unexpected errors.

	約
						-R				-T
			2A/1			5A/COM			0.5A/1	2A/COM
									5~30VDC
		250V AC, 30V DC							(UP, ZP	24V DC -15% ~ +20%
										1mA/ )
				75VA					15W/1
重量（約 ）		：		90W				：	； ：Off → On 30us	On：→ Off；100us：
					； 10ms：		入
類型	數位輸入				或
形式	直流（
最電（反動輸入點大壓流出轉應作位負規換時電載格形間準流取式樣時間）			，（，由點繼約（電電器阻以感以及性下上可輸）以）作出下 點 電 氣的調整）規 格 必須外額加定輔消助電點耗點電晶（，約（源體電阻性點））