Hughes AN4-074-DF installation manual Polarization

Page 65

7.While watching the signal strength number to ensure that it stays at maximum, tighten the elevation nuts in the following sequence:

a.Snug the left nut but do not completely tighten it.

b.Snug the right nut but do not completely tighten it.

c.Fully tighten the left nut (torque to 12 ft-lbf).

d.Fully tighten the right nut (torque to 12 ft-lbf).

Adjusting polarization Polarization refers to rotation of the antenna (as shown in Figure 44) and is measured in degrees from zero (no rotation), positive or negative. Polarization is positive east of the satellite longitude and negative west of the satellite longitude.

Figure 44 illustrates how you adjust the antenna’s polarization by rotating the antenna.

Polarization

T0145008

Figure 44: Adjusting elevation

To adjust polarization, follow these steps:

1.Fine-tune the polarization setting by loosening the polarization nuts just enough to enable you to rotate the antenna reflector a few degrees in each direction. If the signal strength does not change, set the polarization to the value calculated by the installation software. Otherwise, set the polarization at the setting where you peaked the signal.

2.While monitoring the signal strength number to ensure that it stays at maximum, tighten the polarization nuts.

Chapter 5 • Pointing the antenna 1035567-0001 Revision A

49

Image 65
Contents Installation Manual for Ku-band Antenna Model AN4-074-DF Copyright 2004, 2005 Hughes Network Systems, LLC Types of warnings used in this manual Important safety informationAntenna installation safety Important safety information 1035567-0001 Revision a Important safety information 1035567-0001 Revision a Vii Viii Contents Chapter Cabling and connections Figures Xii Tables Xiv Scope and audience Organization About this documentRevision record Broadband satellite system components OverviewShows the .74 m antenna installed on a pole mount Install the antenna on the mount Antenna installation overviewMount Installation Guide HNS Tasks related to antenna installationAntenna kit components Antenna parts and required toolsAz/el cap Feed arm unattached Trimast or other antenna mount Details Quantity Small hardware listTool Details ToolsAntenna Site Preparation and Mount Installation Guide Installing the radio and antenna assembliesDetermining the pointing values Revolving plate Assembling the Az/El capAligning the Az/el cap bolts Antenna adjustments for elevation and polarization Installing the Az/El cap onto the antennaElevation Locating the elevation reference edge Polarization Placing the Az/El cap on the antenna reflector Installing the fine elevation pointing tool Shim location next to Tria Installing a shim for vertical transmit polarizationTria Direction of Tria rotation for vertical polarization Horizontal polarization Securing the O-ring Installing the radio assembly on the feed armRadio assembly installed on the feed arm Connecting the feed arm to the antenna reflectorInserting the wedge nut bolt Installing the antenna assembly onto the mast Feed horn groove Attaching the optional shroudShroud screws Cabling and connections Routing the cables at the ODU Transmit and receive cable configurationsConnecting the transmit and receive cables Connecting the receive cable to the LNB Ground screw on the transmitter Ground connectionCabling and connections 1035567-0001 Revision a Pointing the antenna Antenna pointing overview Using the installation software Peaking the signalOPI optional tool OPI Prerequisites for antenna pointing Adjusting azimuth, elevation, and polarization Adjusting the antennaPointing adjustments on Checking the azimuth, elevation, and polarization settings Imu Receive pointingPointing the antenna 1035567-0001 Revision a Elevation nuts Pointing the antenna 1035567-0001 Revision a Polarization Isolating the transmit signal Pointing the antenna 1035567-0001 Revision a Removing the fine elevation pointing tool Final stepsAcronyms and abbreviations Acronyms and abbreviations 1035567-0001 Revision a Index Index 1035567-0001 Revision a

AN4-074-DF specifications

The Hughes AN4-074-DF is an advanced military communication system designed to deliver reliable and secure data transmission in diverse operational environments. Built with cutting-edge technologies, this system plays a critical role in enhancing situational awareness and facilitating effective communication among military personnel.

One of the primary features of the AN4-074-DF is its robust design, which allows it to withstand harsh conditions, including extreme temperatures, humidity, and shock. This durability is essential for military operations, where equipment is often exposed to challenging environments. The system incorporates advanced materials and engineering techniques to ensure longevity and reliability.

The AN4-074-DF utilizes state-of-the-art encryption technologies that provide secure communication channels, making it difficult for adversaries to intercept or decipher sensitive information. This is crucial for military operations where the security of data transmission can significantly influence mission success. The system employs various encryption standards that conform to military specifications, ensuring that it meets stringent security requirements.

Another key characteristic of the AN4-074-DF is its versatility. It is designed to support multiple communication protocols, enabling interoperability among different military platforms and systems. This flexibility allows for seamless integration into existing military networks, enhancing operational effectiveness and coordination among units.

The system also boasts an intuitive user interface, which streamlines operations and minimizes training time for personnel. The user interface is designed for ease of use, allowing operators to focus on their mission rather than struggling with complex technology. This feature is particularly advantageous in high-stress situations where quick decision-making is vital.

In addition to its communication capabilities, the AN4-074-DF is equipped with advanced situational awareness tools. These tools provide real-time data and analytics, helping military leaders make informed decisions based on current battlefield conditions. The ability to access critical information rapidly can be a game-changer in dynamic military operations.

Overall, the Hughes AN4-074-DF stands out as a highly capable communication system that meets the demanding needs of modern military operations. With its durability, security features, versatility, user-friendly interface, and advanced situational awareness capabilities, it plays a pivotal role in enhancing communication and coordination among military forces. This system exemplifies the ongoing evolution of military technologies aimed at improving operational efficiency and effectiveness on the battlefield.