Chauvet DMX5F, DMX5M user manual General Troubleshooting, Setting T HE ST Arting Address

Page 17

SETTING T HE ST ARTING ADDRESS

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that uses 6 DMX channels and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap, and note the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol, we suggest jumping to the Appendix Section and reading the heading “DMX Primer”. It contains very useful information that will help you understand its use.

General Troubleshooting

Symptom

Solution(s)

Applies to

 

Foggers

 

Dimmers

Lights

& Snow

Controllers

& Chaser

 

 

 

 

 

Auto shut off

Check fan thermal switch reset

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Beam is very dim or

Clean optical system or replace lamp

 

 

 

 

not bright

Check 220/110v switch for proper setting

 

 

 

 

 

 

 

 

 

 

 

 

Breaker/Fuse keeps

Check total load placed on device

 

 

 

 

blowing

 

 

 

 

 

 

 

 

 

 

 

 

 

Chase is too slow

Check users manual for speed adjustment

 

 

 

 

 

 

 

 

 

Device has no power

Check for power on Mains.

 

 

 

Check device’s fuse. (internal and/or external)

 

 

 

 

 

Fixture is not

Check DMX Dip switch settings for correct addressing

 

 

 

 

responding

Check DMX cables

 

 

 

 

 

 

Check polarity switch settings

 

 

 

 

 

 

 

 

 

 

 

 

Fixture is on but

Make sure you have the correct audio mode on the

 

 

 

 

 

there is no

control switches. If audio provided via ¼” jack, make

 

 

movement to the

sure a live audio signal exists

 

 

 

 

 

audio

Adjust sound sensitivity knob

 

 

 

 

 

 

 

 

 

 

 

 

Light will not come

Some discharge lamps require a cooling off period

 

 

 

 

on after power failure

before the electronics in the fixture can kick start it

 

 

 

 

 

 

 

 

 

 

again, wait 5 to 10 minutes before powering up

 

 

 

 

 

 

 

 

 

 

 

 

Loss of signal

Use only DMX cables

 

 

 

 

 

 

Install terminator

 

 

Note: Keep DMX cables separated from power cables

 

 

 

 

 

 

or black lights.

 

 

 

 

 

 

 

 

 

 

 

 

Moves slow

Check 220/110v switch for proper setting

 

 

 

 

 

 

 

 

 

 

 

No flash

Re-install bulb, may have shifted in shipping

 

 

 

 

 

 

 

 

 

 

 

No laser output

Bounce mirror motor may have shifted during shipping,

 

 

 

 

 

readjust

 

 

 

 

 

 

 

 

 

 

 

If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on the next page.

Scorpion™ Storm RGX User Manual

17

4/27/2009 5:13 PM

Image 17
Contents Snapshot Table of Contents AC Power What is includedBefore YOU Begin Unpacking InstructionsSafety Instructions Stop and Read ALL Laser Safety Data NON-INTERLOCKED Housing WarningLaser Safety Label Reproduction Laser Emission Data Laser Light Avoid Direct EYE ExposureDMX Channel Summary FeaturesIntroduction Product Overview Product Dimensions Proper Usage Fuse Replacement SetupMounting RI ENT AT I O NData Cabling Fixture LinkingDMX DAT a Cable Cable Connect ORSMaster/Slave Fixture Linking Setting up a DMX Serial Data LinkPIN to 5- PIN Conversion Chart Menu Functions Operating InstructionsNavigating the Control Panel DMX Channel Values Control ModeColor selection StrobeSetting T HE ST Arting Address General TroubleshootingAppendix Returns ProcedureTechnical Support DMX PrimerClaims Technical Specifications