Christie Digital Systems 38-VIV401-01 user manual To change code of Projector

Page 41

SETTING

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1.When any input signal is interrupted, “No signal” and counting down display appears (for 5 minutes).

2.After counting down for 5 minutes, projector lamp and READY indicator are turned off.

3.When READY indicator flashing, Projection Lamp can be turned on again (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when input signal connected or projector is operated with any button on Side Control or on Remote Control Unit again.

On start

When this function is “On,” projector is automatically turned on just by switching MAIN ON/OFF SWITCH on.

Note ; Be sure to turn projector off properly (refer to section “TURNING OFF PROJECTOR” on P22). If projector is turned off in wrong steps, On Start function does not operate properly.

Time left until Lamp off.

Press SELECT button at this icon to display other items.

On start

Press SELECT button at this icon to display previous items.

Move a pointer to item and then press POINT LEFT/RIGHT button(s).

Lamp Mode

This Projector is equipped with 4 Projection Lamps and a number of using lamps can be switched to 4 lamps or 2 lamps. Using 2 lamps maintain life of Projection Lamps.

To change over Lamp Mode

1.Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select SETTING and press SELECT button. Setting dialog box appears.

2.Press POINT DOWN button to move a red frame pointer to “Lamp mode”. Set "4 lamps mode" or "2 lamps mode" by pressing POINT LEFT/RIGHT button(s). When Lamp Mode is set from "4 lamps mode" to "2 lamps mode" image becomes little darker. When Lamp Mode is set from "2 lamps mode" to "4 lamps mode" image become brighter gradually.

NOTE : After changing Lamp Mode, it cannot be switched again for 90 seconds.

Remote control

This projector has two different remote control codes; factory-set normal code (Code 1) and secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.”

To change code of Projector;

Set Remote control in SETTING MENU to “Code 2.”

To change code of Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.

After changing code, make sure Remote Control operates properly.

To return to normal code (Code 1), operate both projector and Remote Control in ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL-OFF switch is turned to “ALL-OFF,” remote transmit code automatically returns to normal code (Code 1).

41

Image 41
Contents Model Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationFor U.S.A. and Canada For Continental Europe SETTING-UP ProjectorConnecting AC Power Cord Positioning Projector Preparation Lens InstallationLens Shift Adjustment Moving Projector Preparation Picture Level and Tilt AdjustmentTerminals of Projector Connecting ProjectorReplacement of Terminal BNC Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Input Jacks AV Input VIDEO/Y, C JacksSerial Port Terminal Reset ButtonSerial Port OUT Terminal JackTerminals Projector Connecting to ComputerTerminals Connecting to Video EquipmentSide Controls Side Controls and IndicatorsBefore Operation Ready Indicator IndicatorsLamp Indicator Lamp Replace IndicatorLaser Pointer Function Operation of Remote ControlWired Remote Jack Volume ButtonZoom Button Focus ButtonFlow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Before Operation Menu BAR Turning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorZoom Adjustment Adjusting ScreenFocus Adjustment Keystone AdjustmentNo Show Function Timer FunctionBasic Operation Picture Freeze Function Direct Operation Sound AdjustmentMenu Operation Sound MenuSelecting Input Source Computer InputSelecting Computer System InputSelect Computer System Manually Computer Input Automatic MULTI-SCAN SystemAuto PC System MenuResolution Computer Input Compatible Computer SpecificationsAuto PC Adjustment PC AdjustmentPC Adjust Menu Computer InputComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Image Level Select Direct Picture Image AdjustmentImage Level Select Menu Image 1~4Image Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 2 5 BNC SlotSelecting Video System Component Video Signal FormatVideo Input PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Color Video Input Image Level AdjustmentTint Noise reductionProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Projector To change code of Remote Control UnitProjector mode Wireless Mouse modeLamp counter reset USBMaintenance Operating Wireless MouseInstallation Operating Wireless MouseCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementOrder Replacement Lamp Appendix Lamp ReplacementTroubleshooting Service Technical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsSerial Port IN/OUT Terminal Part No 296 8828 1AA6P1P3040-- MJ6K