Christie Digital Systems 38-VIV211-01 user manual SETTING-UP Projector, Connecting AC Power Cord

Page 8

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-240 V AC. This projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce risk of electrical shock, do not plug into any other type of power system.

Consult your authorized dealer or service station if you are not sure of the type of power supply used.

Connect the projector with peripheral equipment before turning the projector on. (Refer to pages 12 ~ 14 for connection.)

CAUTION

For safety, unplug AC Power Cord when an appliance is not used.

When this projector is connected to the outlet with an AC Power Cord, the appliance is in Stand-by Mode and consumes a little electric power.

Connect the AC Power Cord (supplied) to the projector.

The AC outlet must be near this equipment and must be easily accessible.

CAUTION

The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below. The proper AC Power Cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer.

	Projector side	AC Outlet side
		For U.S.A. and Canada	For Continental Europe
		Ground
	To POWER CORD	To AC Outlet.
	CONNECTOR on the	To AC Outlet.	To AC Outlet.
	CONNECTOR on the	(120 V AC)
	projector.	(120 V AC)
	projector.		(200 - 240 V AC)

8

Image 8

Contents Model 103-004001 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Camden Drive Cypress, CA 90630 USA Table of Contents Features and Design Compact Design Digital Zoom for ComputerHOT AIR Exhausted PreparationName of Each Part of Projector For U.S.A. and Canada For Continental Europe SETTING-UP ProjectorConnecting AC Power Cord Room Light Preparation Lens InstallationPositioning Projector Preparation Adjustable Feet Installing Projector in Proper PositionPreparation Moving Projector Connecting Projector Terminals of ProjectorConnect computer output Digital DVI-D type to this terminal Refer to P13A Projector Connecting to ComputerTerminals Connecting to Video Equipment Operation of Remote Control Inside the Battery Compartment BOXBefore Operation Laser Pointer FunctionRemove battery Compartment lidSlide batteries into CompartmentTOP Controls and Indicators Flow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu Press Menu Button while connecting to PC input source Used to adjust picture imageBefore Operation Menu BAR Used to selectBasic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Keystone AdjustmentFocus adjustment may not function properly if the image is Corrected by Keystone adjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System Rgbav HdcpPC System Menu Automatic MULTI-SCAN SystemAuto PC Adjustment Auto PC AdjustmentPC Adjust Menu Auto PC AdjComputer Input Manual PC Adjustment Full screen Display areaDisplay area H Picture Image Select Image Level Select DirectImage Level Select Menu Image Select MenuPicture Screen Adjustment Screen MenuWhen video input signal is connected to Video jack Video InputVideo Select VideoSelecting Video System AutoAV System Menu Video or S-VIDEO AV System Menu Component VideoPicture level adjusted for picture with fine tone CinemaProvides image at a normal video aspect ratio of 4 Provides image at a wide screen ratio of 16Picture Image Picture Image AdjustmentsImage Adjust Menu List Mode Color temp White balance RedWhite balance Green White balance BlueSetting Menu SettingSetting Menu Anamorphic Blue backDisplay Menu positionTo change the code of the Remote Control Unit Power managementRemote control To change the code of ProjectorWireless Mouse mode Projector modeLamp counter reset Factory defaultOperating Wireless Mouse InstallationOperating Wireless Mouse AppendixStation MaintenanceIndicatorIndicator Appendix AIR Filter Care and Cleaning Cleaning Projection LensRecommendation Pull up and removeLamp Replacement Lamp ReplaceMessage Lamp replace counter reset? is displayed. Move Reset Lamp Replace CounterAppendix Lamp Replace Counter Pointer to Yes and then press Select buttonTroubleshooting Service Appendix Indicators and Projector Condition Appendix Compatible Computer Specifications ResolutionMenu Tree PC sourceSystem Setting Sound Technical Specifications Appendix Configurations of Terminals Control Port ConnectorUSB Connector Series B Computer INPUT-1 and Monitor OUT Terminals AnalogAppendix Optional Parts Lens ReplacementTo the sales and service engineer Appendix Part No -A 610 316 2607 1AA6P1P4324A- MH5KL