BOXLIGHT MP-385T manual To change code of Projector, To change code of Remote Control Unit

Page 36

SETTING

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1.When any input signal is interrupted, “No signal” and counting down display appears (for 5 minutes).

2.After counting down for 5 minutes, projector lamp and READY indicator are turned off.

3.When READY indicator flashing, Projection Lamp can be turned on again (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when input signal connected or projector is operated with any button on Top Control or on Remote Control Unit again.

Time left until Lamp off.

Press SELECT button at this icon to display other items.

On start

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to section “TURNING OFF PROJECTOR” on P19). If projector is turned off in wrong steps, On Start function does not operate properly.

Remote control

This projector has two different remote control codes; factory-set normal code (Code 1) and secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.”

To change code of Projector;

Set Remote control in SETTING MENU to “Code 2.”

To change code of Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.

After changing code, make sure Remote Control operates properly. To return to normal code (Code 1), operate both projector and Remote Control in ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL- OFF switch is turned to “ALL-OFF,” remote transmit code automatically returns to normal code (Code 1).

Lamp counter reset

This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 39 for operation.

On start

Press SELECT button at this icon to display previous items.

Move pointer to item and then press

POINT LEFT/RIGHT button(s).

Move pointer to Lamp counter reset and then press SELECT button. Message “Lamp replace counter reset?” is displayed.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Boxlight MP-385t To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Digital Zoom for ComputerPreparation Name of Each Part of ProjectorSETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Positioning ProjectorPreparation Adjustable Feet Moving ProjectorConnecting Projector Terminals of ProjectorAudio Input Jacks BNC Input JacksConnecting to Computer Terminals A ProjectorConnecting to Video Equipment Audio VideoOperation of Remote Control Before OperationLaser Pointer Function Volume Button Wired Remote JackZoom Button Focus ButtonTOP Controls and Indicators Ready IndicatorHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Guide WindowSound Menu Turning on / OFF Projector Turning on ProjectorTurning OFF Projector Adjusting Screen Zoom AdjustmentLens Shift Adjustment Keystone AdjustmentSound Adjustment When Select Input 1 Computer Input Terminals When Select Input 2 5 BNC Input JacksComputer Input Selecting Input SourcePC Adjustment Auto PC AdjustmentComputer Input Automatic MULTI-SCAN System AutoComputer Input Manual PC Adjustment Computer Input Display areaDisplay area H Full screenComputer Input Compatible Computer Specifications Resolution640 x 31.469 59.940 1024 x 48.363 60.004Picture Image Adjustments Image Level Select DirectImage Level Select Menu Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuWhen Select Input 3 AV Terminals Video InputVideo Component Video Signal Format Selecting Video SystemVideo Input Video Jack or S-VIDEO JackCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change code of Remote Control Unit To change code of ProjectorSETTING/APPENDIX Operating Wireless MouseInstallation Operating Wireless MouseMaintenance AIR Filter Care and CleaningCleaning Projection Lens Appendix Lamp Replacement Order Replacement LampLamp Replace Counter Troubleshooting Service Technical Specifications Appendix Configurations of Terminals USB Connector Series BLimited Warranty Warranty Limitation and ExclusionDisclaimer or Unstated Warranties Limitation or Liability
Top Page Image Contents