BOXLIGHT XP-5t manual Appendix Lamp Replacement, Lamp Replacement Monitor Timer

Page 36

APPENDIX

LAMP REPLACEMENT

When the life of the Lamp of this projector draws to an end, the LAMP REPLACEMENT indicator lights yellow. When the image becomes dark or the color of the image becomes unnatural, replacement of the Lamp is required.

CAUTION

● For continued safety, replace with a lamp assembly of the same type.

● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot.

●Do not drop the lamp assembly or touch the glass bulb! The glass can shatter and may cause injury.

Follow these steps to replace the lamp assembly.

1

Turn off the projector and disconnect the AC plug. Allow the

projector to cool for at least 45 minutes.

2

Cover.Remove the screw with a screwdriver and remove the Lamp

3

Remove the two screws with a screwdriver and pull out the

Lamp Assembly by grasping the handle.

4

Replace the Lamp Assembly with a new one and tighten the two

screws. Make sure that the Lamp Assembly is set properly.

 

Replace the Lamp Cover and tighten the screw.

5

Connect the AC Power Cord to the projector and turn the

projector on.

6

Reset the Lamp Replacement Monitor Timer (refer to the section

“Lamp Replacement Monitor Timer” below).

NOTE : Do not reset the LAMP REPLACEMENT MONITOR TIMER when the lamp is not replaced.

LAMP ASSEMBLY

LAMP COVER

HANDLE

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through Boxlight at 1-800-762-5757 or 360-779-7901. ● Model No. of your projector : BOXLIGHT XP-5t

●Replacement Lamp Type No. : POA-LMP31

(Service Parts No. 610 289 8422)

LAMP REPLACEMENT MONITOR TIMER

Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting.

1

Turn the projector on, and press the MENU button and the ON-SCREEN MENU will appear. Press the POINT

 

LEFT/RIGHT buttons to select SETTING and press the SELECT button (refer to the page 32, 33). Another dialog box

 

SETTING MENU will appear.

2

Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Lamp age,” and then press the

 

SELECT button. The message "Lamp replace monitor Reset?" is displayed.

3

Select [Yes] to reset the Timer.

Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Boxlight XP-5t To the Owner Safety Instructions Voor de klanten in NederlandAC Power Cord Requirement CompliancesTable of Contents Features and Design ComputersColor Systems Component VideoPreparation Name of Each Part of the ProjectorHOT AIR Exhausted Zoom Ring Focus RingSETTING-UP the Projector Connecting the AC Power CordFor Continental Europe Adjustable Feet Preparation Positioning the ProjectorRoom Light Preparation Moving the Projector Connecting the Projector Control Port ConnectorTerminals of the Projector Pb/Cb Pr/CrConnecting to the Video Equipment Connecting the ProjectorTerminals Projector Connecting to the Computer Terminals of the ProjectorControl Cable for PS/2 Port ComputerOperation of the Remote Control Before OperationRemote Control Batteries Installation TOP Controls and Indicators TeleHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Setting Menu Before Operation Menu BARBasic Operation Turning on / OFF the ProjectorTurning on the Projector Turning OFF the ProjectorAdjusting the Image Zoom AdjustmentFocus Adjustment Keystone AdjustmentSound Adjustment Computer Mode Selecting Computer ModeSelecting Computer System Computer Mode Compatible Computer Specifications ResolutionFreq KHzPC Adjustment AdjustTotal lines Total dotsHorizontal / Vertical ClampPicture Image Adjustments Normal FunctionPicture Position Adjustment Computer Mode Auto Image FunctionImage PositionPicture Screen Adjustment Expand functionCompress function Panning functionVideo Mode Selecting Video ModeSelecting Video Source AutoSelecting Color System RegularWide Picture Image Adjustment Adjusting the Picture ImageColor TintSetting Setting MenuPower management Selecting LanguageLamp age Operating Wireless Mouse InstallationOperating Wireless Mouse AppendixMaintenance Temperature Warning IndicatorAIR Filter Care and Cleaning Cleaning the Projection LensAppendix Lamp Replacement Lamp Replacement Monitor TimerLamp Assembly Lamp Cover Handle Troubleshooting Remote Control Unit Wireless MouseDoes not work Function does notTechnical Specifications Limited Warranty
Top Page Image Contents