BenQ MP730 manual Adjusting the projected image, Adjusting the projection angle

Page 33

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine tune the

horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 34 for details.

Do not look into

the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

The screen will be blank while AUTO is functioning.

Fine-tuning the image size and clarity

1.

Adjust the projected image to the size 2.

Then sharpen the image by rotating

 

that you need using the zoom ring.

the focus ring.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Operation 33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Welcome Table of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Bedding or any other soft surface Allow at least 50 cm clearance from wallsResulting in damage to the projector Ceiling mounting the projector Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover Projector Controls and functionsCapture Remote controlOperating the Laser pointer Indicator light 22. D. Zoom +Remote control effective range Replacing the remote control batteriesApprox.15 Positioning your projector Set Rear Ceiling in the System Setup BasicChoosing a location Front TableObtaining a preferred projected image size Page Projection dimensions Floor InstallationCeiling Installation 1708 1834 9961594 2732 2934 100Screen Center of lens Projection distance Maximum zoom Minimum zoom762 1016 2090 22452787 2993 100 1742 18713483 3741 5225 5612Connecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computerConnecting Audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi device Connecting an Hdmi deviceDevice Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceOperation Projection lamp Press I I Power on the projector or remoteStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSecuring the projector Removing the control keypad on the projectorIf you forget the password Setting a passwordTo the Security Settings Respectively represent 4 digitsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordChanging Color Space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone On the projector or remote ControlAbout the aspect ratio Selecting the aspect ratioOperation Selecting a picture mode Using Wall ColorPC Signal Input Optimizing the imageSetting the User 1/User 2 mode Fine-tuning the image quality in user modesAdjusting Brightness Adjusting ContrastAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant Color3D Color Management Every adjustment made will reflect toYou want the timer to show up on the screen by Setting the presentation timerHow to use the Timer ON/SHOW button? To cancel the timer, perform the following stepsRemote paging operations Button is a multi-functional keyFreezing the image Hiding the imageUtilizing FAQ function Go to the System Setup Basic Panel Key LockLocking control keys Operating in a high altitude environment Setup Advanced High Altitude Mode, select OnCreating your own startup screen To activate the High Altitude Mode, go to the SystemAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Personalizing the projector menu displayDisplay prompting you Shutting down the projectorMenu system Menu operationAdvanced BasicSource menu Display menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Care of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Replacing the lamp Loosen the screw that secures the lamp MaintenanceTighten the screw that secures the lamp Restart the projector Resetting the lamp timerIndicators Remote control does not work TroubleshootingProjector does not turn on No pictureProjector specifications SpecificationsMm W x 131.30 mm H x 304.99 mm D 274.87 48.57 Specifications DimensionsHorizontal Vertical Pixel Resolution Frequency Mode KHz MHz Timing chartSignal Format Horizontal Frequency Vertical Frequency KHz Supported timing for PC inputSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputsColor sub Video HdcpLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive

MP730 specifications

The BenQ MP730 is a high-performance projector designed to meet the diverse needs of business and education environments. Recognized for its exceptional image quality and advanced features, the MP730 offers a blend of functionality and ease of use, making it a popular choice among professionals and educators alike.

At the heart of the BenQ MP730 is its high brightness of 3000 ANSI lumens, which ensures vivid, detailed images even in well-lit rooms. This is especially beneficial in classrooms or conference rooms where ambient light can affect visibility. Coupled with a native XGA resolution (1024 x 768), the projector produces sharp and clear visuals, making it ideal for presentations, video conferencing, and educational uses.

The MP730 employs DLP (Digital Light Processing) technology, which enhances the projector's color accuracy and reduces the risk of image distortion. This technology also contributes to the overall reliability of the projector, with a longer lifespan for the lamp, enabling extended operational periods without the need for frequent replacements. Additionally, the 2000:1 contrast ratio ensures that images display rich blacks and bright whites, providing depth to presentations and videos.

Another notable feature of the BenQ MP730 is its extensive connectivity options. It includes VGA, composite video, and S-Video inputs, as well as USB connectivity, allowing users to easily connect various devices like laptops, DVD players, and mobile devices. The inclusion of a built-in speaker further enhances the projector's versatility, making it suitable for multimedia presentations without the necessity of external audio equipment.

User-friendliness is a core characteristic of the MP730. With features such as auto keystone correction, users can quickly adjust images for perfect alignment, while the built-in setup wizard simplifies initial configuration. The lightweight design of the MP730 also facilitates easy transportation, making it an excellent choice for traveling professionals or educators who need to move between different locations.

Moreover, the MP730 demonstrates an environmentally conscious design. Its energy-saving mode significantly reduces power consumption when the projector is idle, with features like the SmartEco technology optimally adjusting brightness to extend the life of the lamp while minimizing energy use.

In conclusion, the BenQ MP730 is a versatile projector packed with features that cater to the needs of business professionals and educators. Its combination of high brightness, rich color accuracy, multiple connectivity options, and user-friendly design makes it an excellent choice for anyone seeking a dependable and effective presentation tool.
Top Page Image Contents