BenQ MP730 manual Restart the projector, Resetting the lamp timer

Page 60

10.Use a coin to turn the screw clockwise until the lamp cover is secured.

Loose screw may cause a bad connection, which could result in malfunction.

Do not over tighten the screw.

11.Restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

12. After the startup logo, open the On-Screen Notice Display (OSD) menu. Go to the SYSTEM

SETUP: Advanced > Lamp Settings menu. Press Mode/enter on the projector or ENTER on the remote control. The Lamp Settings page displays. Highlight Reset Lamp Timer. A warning message displays asking if you want to reset the lamp timer. Highlight Reset and press Mode/enter on the projector or ENTER on the remote control. The lamp time will be reset to '0'.

Do not reset if the lamp is not new or replaced as this could cause damage.

Reset Lamp Timer?

Reset Cancel

60 Maintenance

Image 60
Contents Welcome Table of contents Important safety instructions Refer servicing to qualified service personnelFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Bedding or any other soft surface Allow at least 50 cm clearance from wallsResulting in damage to the projector Ceiling mounting the projector Projector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper side Rear/lower sideLamp cover Controls and functions ProjectorRemote control CaptureIndicator light 22. D. Zoom + Operating the Laser pointerRemote control effective range Replacing the remote control batteriesApprox.15 Set Rear Ceiling in the System Setup Basic Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Page Projection dimensions Floor InstallationCeiling Installation 996 1708 18341594 2732 2934 100Maximum zoom Minimum zoom Screen Center of lens Projection distance762 1016 2090 22451742 1871 2787 2993 1003483 3741 5225 5612Connecting a computer or monitor Connecting a computerConnection To connect the projector to a notebook or desktop computerConnecting Video source devices Connecting AudioBest video quality Better video qualityConnecting an Hdmi device To connect the projector to an Hdmi deviceConnecting a Component Video source device DeviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceProjection lamp Press I I Power on the projector or remote OperationStarting up the projector OperationUsing the menus Use / to highlight the System Setup Basic menuUsing a security cable lock Utilizing the password functionSecuring the projector Removing the control keypad on the projectorSetting a password If you forget the passwordTo the Security Settings Respectively represent 4 digitsEntering the password recall procedure Changing the passwordDisabling the password function Enter a new passwordSwitching input signal Changing Color SpaceAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarityOn the projector or remote Control Correcting keystoneSelecting the aspect ratio About the aspect ratioOperation Using Wall Color Selecting a picture modePC Signal Input Optimizing the imageFine-tuning the image quality in user modes Setting the User 1/User 2 modeAdjusting Brightness Adjusting ContrastAdjusting Color Adjusting TintAdjusting Sharpness Adjusting Brilliant ColorEvery adjustment made will reflect to 3D Color ManagementSetting the presentation timer You want the timer to show up on the screen byTo cancel the timer, perform the following steps How to use the Timer ON/SHOW button?Remote paging operations Button is a multi-functional keyHiding the image Freezing the imageUtilizing FAQ function Go to the System Setup Basic Panel Key LockLocking control keys Setup Advanced High Altitude Mode, select On Operating in a high altitude environmentCreating your own startup screen To activate the High Altitude Mode, go to the SystemAdjusting the sound Adjusting the sound levelTurning off the Power on/off ring tone Personalizing the projector menu displayShutting down the projector Display prompting youMenu operation Menu systemBasic AdvancedDisplay menu Source menuPicture menu System Setup Basic menu System Setup Advanced menu Information menu Maintenance Care of the projectorSetting Lamp Mode as Economic Setting Auto Power OffLamp information Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Replacing the lampTighten the screw that secures the lamp Resetting the lamp timer Restart the projectorIndicators Troubleshooting Remote control does not workProjector does not turn on No pictureSpecifications Projector specificationsDimensions Mm W x 131.30 mm H x 304.99 mm D 274.87 48.57 SpecificationsTiming chart Horizontal Vertical Pixel Resolution Frequency Mode KHz MHzSignal Format Horizontal Frequency Vertical Frequency KHz Supported timing for PC inputSupported timing for Video and S-Video inputs Supported timing for Hdmi Hdcp inputColor sub Video HdcpWarranty and Copyright information Limited warrantyCopyright DisclaimerRegulation statements FCC statementEEC statement Weee directive

MP730 specifications

The BenQ MP730 is a high-performance projector designed to meet the diverse needs of business and education environments. Recognized for its exceptional image quality and advanced features, the MP730 offers a blend of functionality and ease of use, making it a popular choice among professionals and educators alike.

At the heart of the BenQ MP730 is its high brightness of 3000 ANSI lumens, which ensures vivid, detailed images even in well-lit rooms. This is especially beneficial in classrooms or conference rooms where ambient light can affect visibility. Coupled with a native XGA resolution (1024 x 768), the projector produces sharp and clear visuals, making it ideal for presentations, video conferencing, and educational uses.

The MP730 employs DLP (Digital Light Processing) technology, which enhances the projector's color accuracy and reduces the risk of image distortion. This technology also contributes to the overall reliability of the projector, with a longer lifespan for the lamp, enabling extended operational periods without the need for frequent replacements. Additionally, the 2000:1 contrast ratio ensures that images display rich blacks and bright whites, providing depth to presentations and videos.

Another notable feature of the BenQ MP730 is its extensive connectivity options. It includes VGA, composite video, and S-Video inputs, as well as USB connectivity, allowing users to easily connect various devices like laptops, DVD players, and mobile devices. The inclusion of a built-in speaker further enhances the projector's versatility, making it suitable for multimedia presentations without the necessity of external audio equipment.

User-friendliness is a core characteristic of the MP730. With features such as auto keystone correction, users can quickly adjust images for perfect alignment, while the built-in setup wizard simplifies initial configuration. The lightweight design of the MP730 also facilitates easy transportation, making it an excellent choice for traveling professionals or educators who need to move between different locations.

Moreover, the MP730 demonstrates an environmentally conscious design. Its energy-saving mode significantly reduces power consumption when the projector is idle, with features like the SmartEco technology optimally adjusting brightness to extend the life of the lamp while minimizing energy use.

In conclusion, the BenQ MP730 is a versatile projector packed with features that cater to the needs of business professionals and educators. Its combination of high brightness, rich color accuracy, multiple connectivity options, and user-friendly design makes it an excellent choice for anyone seeking a dependable and effective presentation tool.