BenQ PB6110 manual Move the latch to another end as shown in the picture

Page 38

Step 1. Turn the power off and disconnect the projector from the wall socket. Step 2. Turn the projector over. Then loosen the

screws and remove the lamp cover. If the lamp is hot, avoid burns by waiting for 45 minutes until the lamp has cooled.

Step 3. Move the latch to another end as shown in the picture.

Step 4. Loosen the screw that holds the lamp to the projector. If the screw is not loos- ened completely, they could injure your fingers. It is strongly recommended that you use a magnetic-head screwdriver.

Step 5. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector.

Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

Do not insert your hands into the projector after the lamp is removed. If you touch the optical com-

ponents inside, it could cause color unevenness and distortion of the projected images.

Step 6. Insert a new lamp. Make sure the handle is fully locked, move the latch back, and tighten the screw firmly.

Loose screw may cause a bad connection, which could result in malfunction.

Do not over tighten the screw.

Step 7. Re-install the lamp cover and tighten the screw. Do not turn the power on with the lamp cover removed. Whenever the

lamp is replaced, reset the total lamp operation time. Do not reset if the lamp is not replaced as this could cause damage.

34 Maintenance

Image 38

Contents Welcome Copyright DisclaimerTable of Contents Iv Table of Contents Ordering Parts or Getting InformationBut could fail if power cuts or surges Important Safety InstructionsRefer servicing to qualified service personnel Important Safety InstructionsSafety Instructions May result in a fire Using the unit when it is not fullyBedding or any other soft surface Zontal surface during operationSafety Instructions Projector Features IntroductionShipping Contents Projector Exterior View Alternative AccessoriesOptional Accessories Front / Upper SideBottom Side Connector PanelFront adjuster foot Lamp door Rear adjuster foot Controls and Functions External Control PanelRemote Control Description Functions DescriptionsRemote Control Effective Range Installing or Replacing the BatteryConnection Connecting to a Laptop or Desktop ComputerConnection AV equipment Connecting Equipment to the Component Video InputConnecting Video and S-Video Devices Video devices Video cableConnecting to Display Devices Video devices Video cable Audio cableIV. Ceiling rear InstallationChoosing a Location Focus ring Zoom ring Installation Adjusting the HeightPress the adjuster button again to retract the foot Screen SizePB6110 Svga / PB6210 XGA screen size chart 43 aspect ratio PB6110 Svga / PB6210 XGA screen size chart 169 aspect ratioOperation OperationStartup Disconnect the power cord from the wall socket ShutdownFor example Press / on the remote control to display the status barDigital Keystone Correction Auto Adjustment Source SelectionSlide Operation Zoom / FocusingBlank You can set the blank timePresentation Vivid Video Economic Preset Mode SelectionFreeze Menu Operation Menu SystemPicture menu Using the MenusOr 6/ 5on the remote control to select KeystoneKeystone Preset ModePicture Menu BrightnessAs above ColorTint Increases or decreases the color intensity of the imagePro-Picture Menu Reset Setting MenuVolume OSD Time MuteAdvance Menu Source Resolution Information Menu Lamp HourCleaning the Projector Case MaintenanceCleaning the Lens Storing the ProjectorMessage Status Lamp InformationReplacing the Lamp Move the latch to another end as shown in the picture Resetting the lamp counter IndicatorsLight Status & Description Power Temp Lamp Power events Temp InformationProjector needs 110 seconds to cool down. Or Light Status & Description Power Temp Lamp Lamp eventsThermal events Please contact your dealer for assistanceOptional Accessories not included in the standard package Service InformationAccessories included in the standard package Ordering Parts or Getting InformationMake sure that it is switched on TroubleshootingPlug the power cord into the AC inlet on Cause RemedySpecifications Projector SpecificationsSupported Timing for Component-YPbPrInput Timing ChartSupported Timing for PC Input Supported Timing for Video and S-Video InputsDimensions Unit mm DimensionsWarranty WarrantyLimited Warranty EEC Statement Regulation StatementsFCC Statement MIC Statement