|
|
|
|
|
| 41 |
| ||
|
|
|
|
|
|
|
|
| |
9 | Image is too small |
| • | Adjust the zoom lever on the top of the projector. |
|
| English | ||
| or too large |
| • | Move the projector closer to or further from the |
|
| |||
|
|
|
|
| |||||
|
|
|
|
|
| ||||
|
|
|
| screen. |
|
|
|
| |
|
|
| • | Press "MENU" on the control panel or remote |
|
|
| ||
|
|
|
| control. Go to "Image" > "Aspect Ratio" and try |
|
|
| ||
|
|
|
| different settings. |
|
|
| ||
|
|
|
|
|
|
|
|
| |
10 | Image has slanted |
| • | If possible, reposition the projector so that it is |
|
|
| ||
| sides |
|
| centered on the screen and below the bottom of the |
|
|
| ||
|
|
|
| screen. |
|
|
|
| |
|
|
| • | Press the Keystone correction keys on the control |
|
|
| ||
|
|
|
| panel or remote control until the image becomes |
|
|
| ||
|
|
|
| square. |
|
|
|
| |
|
|
| • | Press "MENU" on the control panel or remote |
|
|
| ||
|
|
|
| control to open the OSD menu. Go to "Image" > |
|
|
| ||
|
|
|
| "Auto Keystone (X1140A/X1240/X1340W/P1340W)" |
|
|
| ||
|
|
|
| or "Image" > "Keystone (X111/X1140/H6510BD)" to |
|
|
| ||
|
|
|
| make adjustments. |
|
|
| ||
|
|
|
|
|
|
|
|
| |
11 | Image is reversed |
| • | Select "Image" > "Projection Mode (X1140A/X1240/ |
|
|
| ||
|
|
|
| X1340W/P1340W)", "Image" > "Projection Location |
|
|
| ||
|
|
|
| (X1140A/X1240/X1340W/P1340W)" on the OSD and |
|
|
| ||
|
|
|
| adjust the projection direction. |
|
|
| ||
|
|
|
|
|
|
|
| ||
Problems with the Projector |
|
|
|
| |||||
|
|
|
|
|
|
| |||
# | Condition |
|
|
| Solution |
|
|
| |
|
|
|
|
|
| ||||
1 | The projector stops responding |
| If possible, turn off the projector, then |
|
|
| |||
| to all controls |
|
|
| unplug the power cord and wait at least 30 |
|
| ||
|
|
|
|
|
| seconds before reconnecting power. |
|
| |
|
|
|
|
|
|
| |||
2 | Lamp burns out or makes a |
|
| When the lamp reaches the end of its useful |
|
|
| ||
| popping sound |
|
|
| life, it will burn out and may make a loud |
|
| ||
|
|
|
|
|
| popping sound. If this happens, the projector |
|
| |
|
|
|
|
|
| will not turn on until the lamp module has |
|
| |
|
|
|
|
|
| been replaced. To replace the lamp, follow |
|
| |
|
|
|
|
|
| the procedures in the "Replacing the Lamp" |
|
| |
|
|
|
|
|
| section. |
|
| |
|
|
|
|
|
|
|
|
|
|