Barco R9001190 manual Switching to stand-by, Switching off, Input connections

Page 13

Connections

When the total run time of the lamp is 720 hours or more, the following message will be displayed for 1 minute. This message will be repeated every 30 minutes. Press EXIT to remove the message before the minute is over.

When the total run time of the lamp is 750 hours or more, the following message, with the exact run time is displayed on the screen.

Lamp run time is 750 hours. Operating the lamp longer than 750 hours may damage the projector. Please replace the lamp.

When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.

The total lifetime of the lamp for a safe operation is 750 hours max. (normal power mode). Do not use it longer. Replace always with a same type of lamp. Call a BARCO authorized service technician for lamp replacement.

Warning : Using a lamp for more than 750 hours is dangerous, the lamp could explode.

Lamp run time 720 h

WARNING

Lamp run time is 750 hours Operating the lamp longer

than 750 hours may damage the projector.

Please replace the lamp

<ENTER> to continue

Switching to stand-by.

When the projector is running and you want to go to stand-by, press the stand-by key.

Switching off

To switch off:

-press first STANDBY key and let cool down until the fans stop blowing ( or at least 15 min).

-switch off the projector with the power switch.

Input connections.

The projector has modular input facilities. The input slots can be filled up with the following modules :

Video, S-video (PAL, SECAM, NTSC) input order no. R9827900

RGBS/RGsB analog input order no. : R9827910

RGB3S/RG3sB input order no. : R9827920

Component Video input order no. : R9827930

The sequence of insertion has no importance. It is even perfectly possible to insert several input modules of one type.

Note : When using a RCVDS05 or VS05, the input configuration of the projector must be as follows:

Slot 1 : video input module

Slot 2 : RGB analog input module

Slot 3 : Component input module

Input module insertion into the projector :

-Power down the projector and disconnect the power cord from the wall outlet.

-Remove the dummy plate covering the chosen input slot by turning

out both screws. - Slide the input module in the free slot. Insure the module is seated correctly in the guide grooves. - Press on both handles of the input module until the module plug seats in the connector of the projector. - Secure the input module by tightening both retaining screws. - Reconnect the power cord to the wall outlet and switch on the

projector.

The new installed module can be selected with the digit buttons on the RCU or the local keypad.

4-2

 

5975398 BARCODATA 3200 110797

 

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Date Art. No 110797 R5975398 Barco Projection SystemsFederal communication commission FCC statement Table of Contents Starting up the Installation Mode Unpacking Unpacking & DimensionsBattery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?Componentvideo Separate SyncFront panel terminology Location and Function of ControlsControl Panel Terminology Remote controlRCU Switching on Power mains cord connectionConnections FusesSwitching off Switching to stand-byInput connections Input module insertion into the projectorVideo/S-video input module InstallationRGB analog input module Enter Component input moduleRGB3S/RG3sB input module Set up of the baud rate for communication with a computer Connecting a VS05 to the projector Connecting a Rcvds 05 to the projectorConnecting an IR Remote Receiver 800 to the projector Controlling How to use the RCU?Projector address How to program an address into the RCU? How to display a projector address?Picture controls with direct access Sound controls with direct accessPause key Adjustment Mode Start UP of the Adjustment ModeFile service Starting up the Random Access Adjustment ModeAdjustment Mode Load EditLoad file Random Access Adjustment ModeEdit File Edit fileConfirm Read AmdsCopy File Rename FileRename File Copy FileDelete File Picture TuningFile Options Still Video Sync slow/fastColor Balance GammaVolume, Balance, Bass and Treble Audio TuningMute Lock OFF/INPUT 1/INPUT 2/INPUTShift GeometrySize GeometryBlanking Side keystoneBlanking ScaleGeometry Options OptionsStarting up the Installation Mode Installation ModeConfiguration How to use the built-in adjustable lensholderHole Indication line Starting up the Service Mode Service ModeService Identification IdentificationHow to enable or disable the password function ? Change PasswordHow to change the password ? Change LanguageLamp Drive Mode Reset Lamp RuntimeLamp Run Time History Preset Input Balance Panel AdjustmentsPreset Input Balance I2C diagnosisStandard Source SET UP Files Intergr MacporMAC6 MAC7Lens Cleaning Procedure Focusing the lensLenses Lenses Source numbers 90 Source Numbers 90Insert Card

R9001190 specifications

The Barco R9001190 is a high-performance projector designed specifically for cinema applications, renowned for its exceptional image quality and technological advancements. This projector is part of Barco's extensive range of digital cinema solutions, catering to the needs of modern theaters and entertainment venues seeking to provide a superior viewing experience.

One of the standout features of the R9001190 is its impressive brightness, capable of delivering up to 20,000 lumens. This high level of brightness ensures that images remain vibrant and clear, even in larger auditoriums where ambient light can dilute the viewing experience. The R9001190 is equipped with DLP (Digital Light Processing) technology, which enhances image precision and color accuracy. DLP is known for producing sharper images with higher contrast ratios, making it an ideal choice for cinematic presentations.

The projector uses a laser light source, providing several advantages over traditional lamp-based systems. Laser technology not only increases the projector's longevity and reliability but also enables a wider color gamut. This translates to richer, more dynamic colors, enhancing the overall visual experience. With consistent brightness levels throughout its lifespan, the R9001190 ensures that theaters do not have to frequently replace components, leading to reduced operational costs.

In addition to its superior image quality, the Barco R9001190 also incorporates advanced feature sets for enhanced functionality. It supports multiple industry standards such as DCI (Digital Cinema Initiative) and IMB (Integrated Media Block), ensuring compatibility with a wide range of cinema content. The projector is designed for easy integration into existing cinema systems, allowing for streamlined upgrades without extensive system overhauls.

Another notable characteristic of the R9001190 is its built-in cooling system, which efficiently manages heat dissipation, promoting longer operating times without performance degradation. Additionally, the projector is created with a modular design, facilitating serviceability and maintenance. This modular approach reduces downtime, allowing theaters to maintain high levels of operation without significant interruptions.

In summary, the Barco R9001190 is a cutting-edge digital cinema projector that combines high brightness, advanced DLP technology, and a durable laser light source to deliver an unparalleled movie-watching experience. Its integration capabilities, along with features designed for ease of maintenance, make it an essential choice for theaters aiming to provide audiences with immersive and visually stunning films.
Top Page Image Contents